Find a professional render repair near you

I need our front solid fence wall and piers rendered / texture coated. Approximately 20m long wall and piers combined. Walls are 400mm high - x 5 Piers average 1.7m to 1.8m high - 7

Hi there, I need a skilled plasterer, renderer, or handyman to repair accidental vehicle impact damage on an external structural carport pillar located right in front of the garage door. The Details: The Damage: There are 3 distinct impact points on the outer corner of the rendered pillar. The render has chipped away significantly on the corner edge, exposing the base material underneath. The Job: You will need to patch the damaged spots, reconstruct/straighten the sharp corner edge, re-apply a matching texture coat, and paint it to match the existing off-white/cream building color. Location: Tarneit, VIC. Photos: Please see the attached photos for a close-up of the damage and a wider view of the carport layout. Looking for someone with rendering/patching experience who can bring their own tools/materials and deliver a clean, seamless blend so the repair isn't noticeable. Flexible with days/times for the right person. Thank you!

I’m looking to have someone repair and re-render a small facade which is approximately 3000mm high by 5500 mm wide.

Paint bottom half of the boundary wall, repair 4 x render cracks and paint around garage door. I will supply paint.

Render brick fireplace down to floor level

- remove one row of bricks from rendered wall - Render top of wall - make sure wall is aligned so front gate can move freely on tracks

I need someone to look at a render issue I have at my house. I think I have been a bit too keen with the whipper snipper and need some advice on repairing the issue.

The rendered facade of my home was damaged during a camera install. It has been touched up, but not to an acceptable standard. I'm looking for surface repair. I have the paint on hand.

Base coat pillars and beams - supply render - base coat only Angle beads installed already

Just demolished an outhouse and need rendering for a feature wall. The size is 2000mm wide x 3000mm high. The corner on the right will need a deeper fill and will most likely return around 100mm on the right hand side wall. Render just the minimum thickness required and a cement colour finish is adequate. Not too sure of tge cost, hence I've put a minimum of $10.00

Quote on plastering job in Coogee

Looking to get my dining room walls re-plastered or white set. Room is approx 3.3x2.5 for scale, three walls as pictured, no ceiling. Two base coats and one top coat. I’ll sand and paint. Preference is for as soon as possible so let me know your availability in your offer.

Rendering to brick pillars and walls

Exterior Render Crack Repair – Reappearing Crack Looking for an experienced renderer / exterior repair specialist to repair a recurring crack in exterior house render. Crack is approx. 90cm long Previously repaired but has reappeared Area has not been painted yet Need repair assessed and properly fixed to prevent further cracking Exterior access is straightforward Please bring your own tools, materials and equipment. Would prefer someone with experience in render repair and crack prevention rather than just patching cosmetically. Please include: Your experience with render/crack repairs What method/materials you’d likely use Availability Quote or estimate

Render work needed infront of the garage

I have a set of fleximount shelving that needs to be installed inside the garage. The garage walls are brick. The mounts need to be drilled into brick and not the mortar. Ive given up trying to get the holes to line up straight. There are approx 48 holes to drill.

Need small textured render repair to front entry wall/corner of house. A pallet was accidentally knocked into the rendered corner near my front door, causing a section of the textured render/coating to chip away (see photo). Looking for someone experienced with render or texture coat repairs who can patch, texture match, and repaint/blend the area neatly. Located in Adelaide. Please quote including materials if possible. Experience with acrylic render/texture coat preferred.

I need a confident handyperson to hang a Rachel Donath Dora Gloss Mirror — a premium fibreglass mirror (70cm × 95cm, 17kg) — on an internal pebbledash render wall. The mirror uses a French cleat hanging system (wall cleat + mirror cleat). The wall cleat needs to be fixed securely into the masonry behind the render. 📦 WHAT’S SUPPLIED: • The mirror (already delivered, in box) • French cleat bracket (included with mirror) • Screws (included with mirror) 🛒 PARTS TO PURCHASE (reimbursed on receipt): Before arriving, please pick up from Bunnings Rozelle (Mullens St, Rozelle): • 4 × M8 heavy-duty masonry anchors (Fischer FUR M8 or Ramset Dynabolt M8) • Estimated cost: ~$20–25 (fully reimbursed) 🔧 TOOLS REQUIRED (please bring your own): • Hammer drill with masonry bit • Spirit level • Screwdriver • Measuring tape • Cable/pipe detector ⚠️ WALL NOTES: The wall is pebbledash render over brick. Anchors must drill through the render and at least 50mm into the brick behind. Standard plastic plugs are NOT suitable — this is why we need the upgraded anchors above. ✅ JOB IS COMPLETE WHEN: • Wall cleat is fixed level and securely into the masonry • Mirror is hung and stable • No cracking or damage to the surrounding render 📬 Please include in your offer: • Your experience with masonry/render walls • Whether you have all tools listed above • Your total price (labour + parts reimbursement)

Rendering patch up under neath balcony to prep for painting. Repair x 1 tile on edge of balcony.

We have a 10m x 1-1.5m rendered wall on our pool where the render is bubbling and coming off. We need the bubbling fixed and patched and the whole wall repainted. Also would like the black diamond tiles removed as well. Ideally this can be done without draining the whole pool. Unsure on budget.