Find an experienced handyman in Darling South

I have an Aqara Roller Shade Driver E1 installed on the wall that controls 3 roller blinds. It used to work fine, but recently the roller chain keeps getting stuck inside the motor when it runs. The other end of the chain seems loose or misaligned amd gets tangled. Need someone to inspect, adjust, or refit the chain so it operates smoothly again

Relocate large clock to another wall. Hang two mirrors Wire and mount two #44 inch TV’s (electrical work required for one tv) I have screws and one bracket. May have to get another bracket from Bunnings or JB.

We are replacing our internal doors. It is a single story house. So we will purchase the doors and handles - we then want someone to install the doors x 7. The door sizes are 6 standard (2040x 820) and 1 is 2040x920. The handles are standard.

Need someone to install steel gate into brick pillar.

My shower screen has come off the frame, with the frame splitting per photos attached. Looking to have this fixed.

Replace broken glass, supply materials.

Hi, A sign post was attached to the fence pales with rope ties and unfortunately due to the wind, the pales have been ripped off as the wood was rotten. Looking to replace thr horizontal beams behind the pales and have the pales reattached. Thanks

I have a couple of lamps I would like converted to cordless touch lamps

Hang 1x large art frame (175cm x 137cm) Hang 5x smaller art frames (A3-A4 size) Screw in 4x Arlo security cameras to various parts of house.

Bunch of nails and random stuff around the house I need to remove. Photo are just examples

Hello, I need two flyscreens fixed. One has come off the railing(?) Keeping it in place and the other has been pushed out by my cat trying to escape. The dimensions are: Bedroom l: 79cm h: 39cm Bathroom : l: 59cm x 67cm There's also a blind that my cat has chewed through the cords that I wanted looked at to see if it can be fixed or needed to be replaced.Blind: l: 237cm h: 211cm. Ideally I would like these fixed next Thursday (9/10) between 3pm and 5:30pm.

Rotten part of window wood needs replaced / repaired

Hi, A little bit of the timber door frame has gone bad as pictured. Looking to replace that little section with fresh wood. Materials not supplied. Thanks

Movement in outdoor tiles has resulted in a gap between tiles before a ledge. Approx 5-6m long. Need someone to gap fill / re caulk to close the gap. Black if possible.

Supply and install weatherseal for our tilt garage door to stop leaves and debris from being blown inside. Garage door is 4810mm wide. We prefer a door mounted seal.

Our gate isn’t closing properly, I think it needs a new piece of wood and nails to hold it in place.

Urgent decking board removal for access point creating for plumbing and digging hole. And create a trap door/access in deck.

Looking to have someone supply and install a seal on our garage door to stop debris from being blown into the garage. Prefer for the seal to be installed on the garage door, not floor. Please provide details of the proposed seal in your offer.

Description: One of the side protective bars (runs along the lower edge of the car body) on my 2016 Honda HR-V has come slightly loose — one of the fixings is broken, causing it to sit slightly ajar. I need someone to securely reattach it so it looks flush with the body again. I’m not particular about how it’s done — zip ties, screws, washers, adhesive, etc. — as long as it’s safe, looks clean, and holds up over time. Photos attached for reference. Ideal for: • Mobile mechanics • DIY car fixers • Anyone handy with car bodywork

I have a Heat n Glo Mezzo 1300 AUB fireplace. It has a RC300 remote. The remote has always worked but this morning it has somehow un-paired itself from the fireplace. The remote is still fully functional, just not communicating with the fireplace anymore. Need help finding the control module for the fireplace, and putting it in pair mode again so that the remote will work again. Fireplace is a 2-sided see through fireplace that's built into a floating wall. I've removed the front panels but haven't been able to obviously see the control module.