Find experienced local carpenters in Glen Iris VIC

I need to install a laminate wood platform above my front facing washer dryer. I have seen and like a platform from Ikea.

Timber framed king size bed connections to the bed head both sides have failed i have the replacement bed slats (5 broke) May need additional support to existing timber feet. Bed is a Seb bed from Castlery

One of the timber boards on my garage door has some rot along the bottom, as shown in the photo. Is it possible to repair and fill the damaged section rather than replacing the whole board? There is another board with a smaller area of rot, approximately 3–5 cm wide and about 30 cm long. The third board only has a small amount of rot at one corner, roughly a 2–3 cm right-angle section. Could you please have a look and let me know whether these areas can be repaired, or if the boards need to be replaced?

Assemble & install 10 IKEA METOD laundry wall cabinets Looking for an experienced cabinet/kitchen installer to assemble and install 10 IKEA METOD wall cabinets in my laundry: 5 × 60 × 37 × 60 cm 5 × 60 × 37 × 100 cm I also have the IKEA METOD suspension rails, hinges and shelves. Cabinets need to be securely wall mounted, level and correctly aligned. Custom doors/fronts will be ordered and installed separately at a later date, so no doors need to be fitted as part of this job. Please bring all required tools and appropriate wall fixings. Experience installing IKEA METOD cabinetry preferred.

Wood has absorbed water. It has bulged and so door won't shut easily. May needs replacing so door can shut. Ideas welcome.

Seeking an experienced handyman to complete final elements of a kitchen renovation. Remove and replace broken tile in kitchen (tile and grout supplied) Fill 7 x small holes in internal walls and ceiling ( Dulux Vivid White for reference) Cut 4 x 125mm holes in cabinetry for rangehood ducting. Ducting in place and secured to rangehood in preparation. Ground-floor apartment with easy access to the private courtyard directly to unit from main road - parking avail. To be completed - Saturday 25th (morning) or Monday 27th July

Looking for an experienced carpenter or joiner to build a strong, custom timber frame/shelf that sits on top of my laundry benchtop to elevate a new 9kg Bosch Heat Pump Dryer (~50kg). The goal is to raise the dryer above the bench to preserve my benchtop space below (for a laundry basket and sink access) without hanging the weight off the drywall. Key Requirements: Load Bearing: The frame must safely support 70kg+ (dryer weight + wet clothes). Vertical legs/uprights must align with solid cabinet support beneath the benchtop to transfer weight safely down to the floor. Dimensions: Top Shelf: Approx. 600mm (W) x 650mm (D) to fit the Bosch dryer footprint. Clearance Gap: Approx. 350mm–400mm height clearance beneath the shelf so a laundry basket fits easily on the benchtop. Materials: Structural timber (e.g., 45x90mm pine framing or thick structural ply/MDF) with neat finishing or paint-ready edges. Safety & Securing: Anchor the top rear of the frame into the timber wall studs behind the drywall using L-brackets/battens to prevent forward tipping and vibration movement. Supply or place a rubber anti-vibration mat on the shelf platform. Location / Setup: Drywall backing over existing cabinetry in a standard laundry layout. Flexible with timing—happy to coordinate on precise measurements before you cut materials. Please provide examples of previous timber framing, custom shelving, or joinery work when placing your offer!

Wanting to increase the height of the fridge cavity to allow for a taller fridge. Looking for someone to take the inner box out of the top cabinet and cut down and re-fit smaller doors or leave a single exposed shelf.

Hi, I'm looking for an experienced cabinet maker or carpenter to build a custom pull-out drawer underneath my existing oak sideboard to create hidden toy storage. I've attached photos of the sideboard and a concept image of the look I'm after. Existing Sideboard Tara Oak Sideboard Overall size: 1520mm (W) × 520mm (D) × 840mm (H) Space Available 1300mm wide (between the legs) 540mm deep 220mm high What I'd Like One custom full-width pull-out drawer Oak veneer or timber front that closely matches the existing sideboard Full-extension soft-close drawer runners Strong enough to store children's toys Smooth operation on carpet Clean, seamless finish that looks like it belongs with the existing furniture I'm happy for the cabinet maker to recommend the best materials and construction method. Please Include Quote including materials and labour Photos of similar cabinetry/furniture work Estimated turnaround time 📍 Location: Glen Iris, VIC

The new oven needs a shelf to rest on (underneath supports largely in place already but they are not under the sides so it rests crooked) and the back of the cabinet needs to be cut away to provide a small extra depth; very easy access from the front Addtionally, 4 doors need 15 mm cut off the bottom and reinstal on the existing hinges (the doors are alreay off and in the garage); 2 are simple small BIR hollow doors, 2 are WIR MDF doors Also, install 3 strips of melamine as "sight gurards" under 3 shelf edges in the WIR (roughly 2 x 450mm, 1 x 1.2m ) I have the shelf (needs to be cut down from 600x900) and the melamine strips (cut to height - 50mm) - you need to dock to length

Location: Glen Iris, VIC | Vacant apartment | 5th floor, lift access Looking for an experienced handyman or cabinet installer to complete several small cabinetry tasks in a single visit. All IKEA components supplied — you bring tools and consumables. ACCESS AND PARKING - 5th floor, lift access - Allocated car park on site, height limit 2.2m - Power connected on site (needed for saws/drills) TASKS 1. Install IKEA METOD wall cabinet (Photo 1) - Size 60x37x60cm, plasterboard wall, above sink - Bottom of cabinet at 1.5m height - 3 wall studs confirmed at this position - Cut and mount METOD suspension rail into studs - Tasker to supply and select appropriate screws/anchors for stud fixing 2. Cut and seal EKBACKEN worktop - Cut one 62cm length from the 186cm worktop - Seal the cut edge with provided edgebanding (bring contact adhesive) - Offcut (approx 124cm remaining) is yours to keep 3. Cut FORBATTRA plinth: two lengths, 59.5cm and 50cm 4. Cut METOD suspension rail to 59cm, deburr edges 5. Cut 8x UTRUSTA shelves for existing cabinet (Photo 2) - From 36.4x35cm, trim 4.8cm off one side and 7cm off back, finished size 31.6x28cm - 16 cuts total, no edge sealing required - Fine-tooth blade or track saw required, no chipping 6. Drill 26 shelf pin holes in existing cabinet (Photo 2) - 5mm diameter, 8mm depth - Approximate positions marked with blue tape - Jig and depth stop required, must not pierce cabinet walls - Pins supplied All work is inside the apartment. Please bring drop sheets to protect hybrid floorboards. Please take all offcuts/rubbish generated from cuts with you when you leave. WE PROVIDE: IKEA components (cabinet, rail, worktop, plinth, shelves), pins. YOU BRING: track saw/fine blade, drill + bits, depth stop, shelf pin jig, level, measuring tools, screws/anchors, contact adhesive, drop sheets. Please quote labour plus any extra materials, and your availability. Photos of past cabinetry work welcome.

Repair/replacement of kitchen draw and door hinges

Seeking a qualified cabinetmaker/carpenter to modify a kitchen alcove to fit a larger fridge. The work required is as follows: Carefully remove the vertical end panel on the left side of the fridge that supports the overhead cabinets. Ensure the overhead cabinets remain securely fixed to the wall after the support panel is removed. Remove the door from the passage to the kitchen to create an open entry. Please indicate whether your quote includes removal of the old panel, door, and timber from the site, and provide pricing both with and without removal.

Need repairs to undersurface on sections of a roof eave plus some blocking at base of valleys to stop possums getting in. Plus possible other work around house. Must be experienced trade person

Hi I have two drawers using Samet SmartSlide undermount runners that will no longer engage or stay closed. The locking clips are firing (clicking) but failing to catch the rail. I need a specialist to: ​Diagnose if the 2D Locking Devices need replacement or if the cabinet is out of square. ​Adjust/realign the system to ensure smooth operation. ​Requirements: Experience with Samet, Blum, or Hafele concealed runner systems is essential. Price does not include parts to be discussed once problem is found and if needed.

Title: Install Timber Brackets for Pendant Lights (4.8m Ceiling – Scaffold Provided) Description: Looking for a qualified handyman/carpenter (or experienced installer) to install timber support brackets for pendant lights in a commercial/warehouse-style space. Scope of works:     •    Install timber supports for 3m long pendant lights     •    Ceiling height approx. 4.8m     •    Scaffold is provided onsite     •    Ceiling is roof tiles with steel beams above     •    Exact fixing points are already marked out on the floor and can be transferred straight up to the ceiling using a laser     •    Timber needs to be installed hard up against the ceiling     •    Fixings will be through roof tile into timber supports     •    One existing section (see photo) just needs to be battened out closer to the ceiling Requirements:     •    Experience working at heights     •    Own tools, fixings, and laser level preferred     •    Ability to fix securely into structure (steel/roof framing awareness preferred)     •    Good attention to alignment as pendants are a visible feature Additional info:     •    Easy access with scaffold set up     •    Straightforward job for the right person     •    Potential for ongoing work if done well

The side of this drawer has been damaged over the years. I need a carpenter to replace the pieces of damaged wood, put the sliders back on properly and getting the drawer sliding again. Note the wooden facade of the drawer can be taken off so the carpenter can replace the damaged piece/pieces and then replace the front of the drawer. Must be done on a weekend, Friday or Saturday.

Need a joiner to: Adjust draws and cupboards Install 3 push catches Replace 1 draw slider Install dishwasher integrated front

I have 5 windows exterior 2 large and 3 small single panel to be sanded back and stain reapplied twice. Will need to return on 2nd for 2nd coat. I will supply stain system marine grade. Must have experience doing painting staining and prep etc

Rotten wood needs replacing. Vertical beam is loose floorboard base lifting