Find experienced local carpenters in Mont Albert North

Is about of installing the kitchen cabinet to cover the rangehood which you had provided a quotation for me a while ago

Need a cupboard and draw around fridge for bar

Need someone ASAP to help fit a wine cabinet into a built-in cavity. Scope of work: 1. Remove a section of skirting board on the right side of the cavity 2. Remove the side support strip, trim it shorter, then refit it – to widen the opening so the cabinet can slide in Very small job – should not take long. Must have own tools. Finish quality is important – the result should look clean and tidy, not rough. Attention to detail is a must. Please message with your availability today or tomorrow. Thanks!

I have a small wine rack which I need to have some timber cut for it to sit in.

Scope of Work: • Prepare and treat the affected ceiling area to remove visible water stains. • Apply stain-blocking primer to prevent future discoloration. Send me the quote please. • Repaint the ceiling area with matching ceiling paint for a uniform finish.

Need help installing a kaboodle kitchen wine nook. Cabinet has been made, only need help attaching it to the wall, installing the base end panel, kick board (including cutting) & benchtop. Thanks!!

We need to replace these stairs from our laundry door with a small landing and a couple of steps. The reason is that we are going to install a doggy door in this laundry door so that our dog has access to the yard, but are worried that the dog may stumble down the steps at the moment. So ideally the dog goes through the door onto a bit of a landing before going down the steps.

We have floorboards that need to be replaced with Tassie Oak timber after the hearth is removed from the face of fireplace. Then I would like to add nice little bookshelves into the hole and stacked stone around the front. See before and after image for intention. I also need some weatherboards replaced and a study enclosed onto the porch. This cost is only to come and quote if you are interested to connect. Please provide details of expertise.

Need a Carpenter to do some odd jobs around the house. Including changing some weatherboards one in an awkward position on a patio. Will require support as an hourly rate.

Looking to get solid wood doors made for the kitchen, kick boards and end panels. Wanting completely flat doors, and then either a flat or shaker style end panel. Preference is walnut , with minimal grains. Looking to have this job done on the quicker side if possible. We have all the measurements needed for the exact size of doors and draw faces.

I have an uneven floor because of an old fireplace in my dining area. I need a handyman to help make a stand for my cabinets so they look uniform and at the same level. Happy to purchase the needed material. Just need the help.

Needing someone to weld 4 stainless tube frames together. Just the welds, we will do the polishing. (Photo above of shelving is a reference they will look like the sketches) also square tubing not round. We can bring materials to you or you can come to us if easier. We do a lot of jobs that require welding, so we can have further work for you in the future. To confirm $$$ when job accepted.

Water leak has damaged the ceiling and frame around a sky light and stained the plaster and some plaster panels. Looking for an experienced tradesperson who can repair any damage and repaint the ceiling to fix up the area and make it look attractive and clean. A roofer has fixed the leak in the roof already so its just the cosmetic repair needed on the inside.

Need a carpenter with fixing experience to install skirting boards to a new built after floor is installed. 11 or 12 mm MDF skirts of around 240 meters. There is three curved walls of a quarter of a circle. The circle diameter is 1800 mm. Another quarter circle wall with a small diameter. Offer is based on hourly rate. An entrance door will also be needed to install after the skirts are completed.

New timber Stair treads have arrived with a layer of clear coating. Need an experienced professional to sand the clear layer off and apply two layers of stain and a final layer of clear. Material will be supplied. You need to have all the right tools such as an appropriate sander with vacuum and the skills. 31 stair treads (approx 1000 mm long) and 14 risers and three landings approx( 1000x1000 mm). all treads have drops of 65.