Hire a reliable appliance service in Forest Hill

My Sage Barista coffee machine leaks badly when ever I use it. I replaced the group head seal and it was temporarily working again but it’s now broken again and a lot of water leaks out every time I use it.

F 05 Indesit washing machine error

Washing machine door has come off. Need door installed. Issue is hole where hinge sits is loose. So need either longer screws or new hole made.

I need a dishwasher repair technician to inspect and, if necessary, repair my dishwasher. I believe the issue may just be a clogged drain, but I would like an expert to diagnose the problem

Lawn mower repair for Bosch electric mower

The upper hinge on my integrated Hoover washing machine door has pulled out, and the MDF/particle board around the hinge cup is damaged/stripped (see attached photos). Because this is an integrated appliance, the door undergoes a lot of vibration. I am looking for a handyman who can provide a permanent fix. Requirements: - Repair the "blown" wood hole so the hinge sits securely. - Ideally, use a metal hinge repair plate to reinforce the area (preferred method). - Ensure the door is properly aligned and level so it closes flush with the cabinets. - Please bring your own tools and necessary hardware (plates/filler/screws). Note: Needs to be done ASAP.

Need a handyman to repair integrated dishwasher handle? Might be slightly harder job as previously had to use glue to fix the integrated door...

The washing machine leaking water everywhere

1. Remove current integrated dishwasher and remove front panel. 2. Install 3 end panels. They will have to be trimmed or cut to size and then attach to the worktop. Install at 3 x points in photo. 3. Install new integrated dishwasher and drill it to the installed end panels. The new dishwasher is the same as the current installed on so set up should be the same. 4. Reattach front panel of dishwasher.

Gas hob is being replaced with an electric hob and the gas pipe needs capping off

Our upstairs radiators all heat fine, but none of our downstairs radiators have any heat, I’ve bled them which hasn’t worked, so guess either the system might need repressurising or an airlock needs removing. As it’s an old system I’m unsure how to adjust the pressure correctly.

Need to use a large waste compactor for online content

Hello, in preparation for installing a dishwasher I need to: 1) create / adapt a new water inlet for the dishwasher. There is already a washing machine in the same location so should be easy. 2) create / adapt a new water outlet to the sink - perhaps with y-joint - approx 1m from the location where the dishwasher will go

Our SNOO bassinet has stopped moving completely with the light blue, clips / wings plugged in and the sound is working. The engine sounds like it is working but the actual bed is stationary (a few days ago when it was still working there was a loud creeky sound coming from the leg area). Having checked online forums it is likely some O rings/ rubber grommets need replacing. We need someone who has experience with fixing a SNOO to come and fix it.

Our delonghi coffee machine won't send water through. We've tried all of the troubleshooting tips from the website.

Hi there, I’ve just moved into an older flat and need help with a small kitchen plumbing project. Scope of Work: 1.Install a tabletop dishwasher next to kitchen sink -Connect cold water inlet to the mains (next to kitchen sink) -Connect waste outlet into the existing under-sink waste pipe -Drill two holes through the kitchen counter (next to the sink) to pass inlet and waste hoses 2.Replace existing kitchen tap -Remove current tap -Install a new modern swan-neck tap with a pull-out spray (tap will be supplied) Access Details: The dishwasher will be positioned directly next to the sink, and the plumbing junctions under the sink are fairly easy to reach — there is no issue with cutting away additional back board of the rear of cabinet to make access easier, the cupboard is fronted by removable drawers for easier access. Please bring any tools needed.

I think it's the bearings

I think it's the bearings quote with part

I think it could possibly be the bearings that are going. When it spins it is making a very loud noise

A handy man will meet you