Find experienced local tradies in Inner South West Sydney

Need someone to build my 2 person Kylin sauna. It’s flat pack and comes in 3 boxes. If you think it needs 2 people to build I’m happy to assist.

One wall 1 wall is Approx 2400mm high and width 2150mm with Square set finish. You will be sheeting over existing wall You supply material and finish ready for paint.

Help awning arms broken i need them fixed or replaced

Redo kitchen ceiling due to new kitchen exhaust

- surface prep, clean existing bricks with water + wire brush to remove any remaining lime render. - apply render suitable for waterproofing membrane. (ARDEX WR 80 FR) 16m2 - clean up & rubbish removal.

I recently removed an old built-in wardrobe and installed a new one. I now need the areas left behind repaired and finished neatly. The work includes: • Repairing damaged plasterboard on the wall and near the ceiling • Filling holes, gaps and marks left by the old wardrobe • Repairing the exposed strip on the tiled floor with matching tiles or another neat solution • Sanding, priming and painting the repaired areas to match the existing walls I am looking for an experienced handyman who can complete plastering, minor tiling and painting. Please bring the necessary tools and include materials in your offer where possible. Photos are attached.

Looking for a licensed electrician to install two additional power points in a bedroom. One will be near my work-from-home desk for a computer/monitor setup, and the second will be next to the bedside table. The existing power point is on the opposite side of the room. Looking for someone to assess the best option to install the new points and run any required cabling neatly. Please include labour and materials in your offer.

Mount one TV on gyprock wall and about 10 paintings and 1 clock

Gyprocking, set and sanding ready for paint 3 walls 2.4mx3.2m both sides. All materials supplied.

Fix ceiling gyprock it has fallen i will provide the gyprock

Gyprock to see if possible to do

The RCD labelled “Protected Power” (C20, 30mA) trips the instant I switch it on, so all power points are dead. Lighting circuit is fine. Cause is known: insecticide spray went into one power point and the tripping started immediately after. The RCD has been off since and I haven’t touched the outlet. What I need: the affected outlet inspected and replaced, and the circuit tested.

Looking for a Gyprocker to rectify cut out as per picture can be made into door or just sealed and patched and sanded as well pergola ceiling has been patched but needs Sanding ready for painting and any other minor patching on ceiling as per pic

Mount folding table to drywall I need someone to securely attach a folding table/unit to a drywall wall. The table is already assembled and has a base that sits on the floor, so the wall screws will not be carrying the weight of the table. They are mainly there to secure the top of the unit to the wall and prevent it from tipping forward. There are 4 pre-drilled screw holes along the top rear section of the table. The main complication is the skirting board at the bottom of the wall. Because of the skirting, the back of the table cannot sit flush against the drywall. I have therefore bought two boards/spacers the same thickness as the skirting board to sit behind the table and fill the gap. The job would involve: - Positioning the two spacer boards behind the table - Drilling through the existing 4 mounting holes, through the spacer board and into the drywall - Using suitable drywall anchors/fixings to securely hold the unit against the wall - Making sure everything is straight, secure and neatly installed Please see the attached photos, which should make the setup much clearer. Please bring the appropriate screws, drywall anchors/fixings and tools required for the job.

I have an external power point that I need installed by a licenced electrician. I will supply the materials (external weatherproof power point)

I need to replace 2 power points and 2 light switches. 1 set is in the bathroom on a tile and the other is in bedroom. I have the replacement parts. Just need to replace them and fit them on the wall/tiles

I am looking for a fully licensed NSW electrician to supply and install one new extra power point in a bathroom at a single story house in Padstow and able to provide CCEW. Just take extra care of the wall tiles.

Need a licensed electrician to replace 3 light switches, 3 double power points and 1 bathroom batten light fitting. I have already purchased all the replacement fittings. Please install them and test that everything is working properly. Photos attached

Patch up render through out, render one column and do 1m² of russian stamp

Looking for a handyman/ Painter to apply liquid membrane sealant to a residential metal awning roof. Size/Height: The awning is 24m² and approximately 3 metres high. Materials: All sealant is completely supplied on-site. Scope: Give the metal a quick sweep with a broom, then roll on the sealant coat. Requirements: Please bring your own ladder/Broom and roller/extension pole. Must be an independent contractor carrying your OWN PERSONAL ACCIDENT and LIABILITY INSURANCE. Flexible days ( between 15/7/26—23/7/26)Please send through your offers! ***Worker must rely on their own professional expertise and site inspection before commencing work***