Find an experienced handyman in Welshpool

Install pallet racking in a factory. 6 frames (3734 high) and 20 beams. Bolt to concrete floor, Install clips, make sure it is level

Head gasket has gone on the Hilux. Bubbling in coolant reservoir and slight overheating under load. 2012 N70 4x4 3.0D 1KD

Steel sheet on flooring of a walk in freezer has come apart. Needs to be fixed back with rivets.

Mount 2x 65” TVs with their Wall Mounts at work office in Welshpool. You will need to have a stud finder to locate the studs. As we do rent this office the installation needs to be up to code. We open 8 am to 4 pm, Monday to Friday so this would be the best time to install. - Due date: Flexible

2012 Suzuki Jimmy. Installation of new Central locking system - Due date: Flexible

We need someone to assist installing a missing screw on sofas. Start at 8:00am and finish by 12:00pm. Simple task...open cartons from the top, slip over dust cover, and install a 15mm self taping screw. Re-tape the carton and on to the next one. Need to have your own drill and batteries. - Due date: Needs to be done on Tuesday, 24 October 2023 - Due date: Needs to be done on Thursday, 26 October 2023

Burnt out clutch needs to come out - brand new sealed in box one needs to go in - Due date: Before Saturday, 26 August 2023

Warehouse flat roof sheet tasks including, 1- Chop AC pipes from inside the warehouse & Remove 2 of existing Split system AC motors from roof and make good to the area. 2- Take of supporting bracket& Remove small size ventilator motor and duct pipe from roof and make good to area. 3- Certify that materials and workmanship is supported for 2 years. 3- Roof height out side 7mt, inside up to 8/9mt - Due date: Before Saturday, 19 August 2023

1. Replace damaged/stained ceiling tiles both upstairs and downstairs 2. New cabinet and bench top for the kitchen 4. Paint downstairs office and the board room 5. Box out pipe in the board room - Due date: Flexible

Industrial machine that needs casor wheels welded on. I will buy some wheels and I have a forklift to lift the machine so the welding can be done easily. - Due date: Flexible

I have a motor for commercial roller door that needs to be installed. Have seen videos of it done but thing its prob best to get someone who knows. It's a roughly a 3 x 4m commercial door. There are points on the roof to tie the door to during the change. Can provide a pic of the roller door device and bracket that keeps it straight if needed (its just the regular one with 6 arm things that grab the roller door). - Due date: Flexible

5 Ark work ( frames) to be hanged on brick wall inside th office - Due date: Flexible

Looking for a kitchen freestanding pantry cupboard built so suit my new house Best suit a cabinet maker who can build the unit and I pickup and install myself 2400 high 760 wide 600deep Top section of cupboard, double door 1700 high with 6 shelves Bottom section of cupboard will have a two pull out drawers , inside of the two doors will have an basic organiser shelf Any type of timber Basically; You will supply materials and make this cupboard I will pickup and install myself See picture below of the requirements - Due date: Flexible

We’ve got a pressure washing business, we’re getting a new machine installed on our truck so we need the current equipment on there removed. - Water tank - Boiler - Stationary engine - Portable fuel and diesel tank - 2 tool boxes (Pictures attached) - Due date: Needs to be done on Sunday, 30 October 2022

Looking to get pallet racking up in warehouse. It's 3 x 2m tall uprights with 8 x2.7m crossbeams. I also have floor secure things and shims already. Needs to be drilled in. - Due date: Flexible

Needing this picture hung up (Please see photos) Need a permanent fix as sticky things do not work - Due date: Flexible

Move the existing racking system (3 bay wide x 3 bay high) against the main wall. Secure with bolting system. Remove safety backing and store onsite. - Due date: Flexible

Supply and replace 2x office doors. Supply 2x door handle also - Due date: Needs to be done on Wednesday, 20 July 2022

to make only 26 x tops in one piece, 25mm thickness on melamine board size: 1800x1800x750mm deep with front radius all 2mm ABS matching edging All in standard warm white finish don't care if its formica / laminex / polytec board - Due date: Needs to be done on Tuesday, 9 August 2022

two of my FOH Speakers - 15" AVE - Ultra 15" have blow fuses. with what appears to be some 'melt' beside the fuse Need fix as soon as poss. - Due date: Before Tuesday, 19 July 2022