Find trusted local electricians in Inner South Melbourne

One of my smart light switches is not sending commands to the light, I can’t seem turn things on or off or reset. Would like for someone to come and have a look: If a replacement is needed, I have the switch too.

Swapping the pendant light.

Electrical Requirements -Install Nobo heater in bathroom (power supply to be chased into wall). -Remove and replace light fittings in the sunroom and dining room. -Remove existing light fitting in the living room. -Remove kitchen downlights and install strip lighting. -Relocate power outlet in bedroom (solid wall). -Install additional power outlet in the kitchen pantry. -Remove existing bathroom exhaust fan and install a new fan ducted to the roof. Install rangehood. -Remove existing bathroom heater. Owner-Supplied Items - Lights -Nobo heater -Exhaust fan Electrician to Supply -Power outlets and associated electrical materials.

Hi there, I need to hire an electrician to install 2 new pedant lights and fix the downlights that’s not working

Ceiling light fitting damaged by impact from basketball. Batten holder loose from ceiling. Need to secure or replace fitting.

Power point in bathroom is slow to flick light on Want to install 2x power points, one in bedroom, one in reading corner Light switch in children’s bedrooms slow/ faulty Two hobs on gas stove not working Sensor light installed for outside front door

Bosch Series 8 heat pump dryer door latch broke off and fell inside the machine. Model number WTW87564AU/09. Part number might be 0214

photo of the switchboard and property height of the building

Require 1x power point installed as per pic

I’m looking for a licensed electrician to replace 4 existing ceiling light fittings in my house. Scope of work: Remove 4 existing ceiling light fittings Install 4 new batten-fix light fittings (supplied by me) Existing wiring and ceiling connection points are already in place Ensure all fittings are installed safely and tested upon completion Must be a licensed electrician Please provide your license details and any relevant experience Thank you!

Task: Convert 12 Existing Downlight Cutouts from 70mm to 90mm and Install New Plug-In LED Downlights Looking for an experienced handyman with downlight installation experience. Scope of work: • Enlarge 12 existing ceiling downlight cutouts from approximately 70mm to 90mm. • Install supplied 90mm LED plug-in downlights. • Connect lights to existing plug bases. • Ensure all lights are fitted neatly and sit flush with the ceiling. • Clean up any plaster dust/debris afterwards. Materials: • I will supply the new 90mm LED downlights. I’ve got new ones here. • Please bring appropriate tools, including a 90mm hole saw or suitable cutting tools, a ladder, and cleaning equipment. Property: • Apartment in Sandringham, Melbourne. • Existing downlights are already installed and working. • Access is straightforward from inside the apartment. When applying, please include: • Relevant experience with downlight installations. • Confirmation you have the required tools. • Your estimated time should only take between 30-60 seconds each hole Photos of the existing lights and new lights can be provided.

I’m putting a new TV on a wall - there was previously an outlet on the wall that was removed. I need the outlet put back - wires are still there. There is already a cavity in the wall so I’m hoping it will be easy for you! I’m flexible with where the outlet will go. Need it on Tuesday June 2nd or Wednesday June 3rd (anytime after 9:30am)

Looking for a licensed electrician to supply and install a 4-point power outlet (4 GPO) in place of an existing single power point. Important: The existing power point is installed within a skirting board that is 100mm (10cm) high, so the replacement power point must be 100mm high or less to ensure it fits neatly within the skirting board and does not protrude above it. Scope of works: * Supply a white 4-GPO power point. * Remove existing single power point. * Install new 4-GPO power point. * Test all outlets and ensure everything is working correctly. * Dispose of old fitting if required. Notes: * No wall repairs, patching, plastering or painting will be required. * Photos of the existing outlet and the style of outlet I’m looking for are attached. * Looking for a neat, straightforward installation with minimal fuss. I’ve listed this job at $120, so please keep quotes realistic and close to budget where possible. If there are any genuine reasons the cost would be significantly higher, please explain what additional work would be required. Location: Kooyong Timing: flexible

In the kitchen downstairs I have 3 lights that arent working. Id like to take 2 lights from upstairs and install 1 new one to replace these 3. Upstairs, I'd like to install 2 dimmable lights in to the ones that have been taken for the kitchen, and will need the switch to be replaced to control dimming for those 2 lights.

Have 4 down lights that I want replaced. I have the down lights, but just need someone with a really high ladder! The lights are app 3.7m from the floor.

Need an electrician to install 6 outdoor wall lights on weatherboard walls. The lights will go either side of my windows. There is only 1 spot with light fittings, others don't have power right now, so you'll need to run new wiring to 5 points and wire in each light.

I have x2 ceiling downlight's which need replacing. I do not have replacement globes as they are not easily sourced. They are not LED -images for context. *Budget is negotiable

Need an electrician to take a look at some kitchen down lights. They have just been replace however still flickering. It's only 1down light out of the 4 in the kitchen. Have a video however can't post videos in the post

Licensed electricians only. I have a downlight in my powder room that needs replacing. It's an older transformer style that we wish to replace with a modern plug style for future DIY. The model of the current system is in the photos attached.

Bathroom 2 x heater globe replace Hall 2 x globe replace 12’ ceiling Outdoor 1 x censor globe replace 14’