Find trusted local electricians in Inner South Melbourne

Hi, Seeking to get a new power point installed on the wall

Air conditioner is not working

*Edit: changed scope of work to include switchboard replacement* I am looking for a licensed electrician to: - Replace switchboard - Re-terminate all circuits - Install a dedicated 15A weatherproof outdoor power point that will be used for regular overnight EV charging - Investigate and fix an issue with one bedroom light that appears to be related to the circuit (light not working reliably / suspected wiring or circuit fault). Property details: - Single-storey weatherboard house - Outdoor installation location near driveway / parking area - There is already an existing light switch near the proposed power point location, which may help with access to the circuit or cable routing Scope of work: - Replace switchboard - Outdoor power point - Supply and install 1 × 15A outdoor-rated weatherproof socket (IP55 or similar) - Run new dedicated circuit from switchboard - Install appropriate RCD / RCBO protection - Secure cabling in conduit suitable for external wall - Test and certify installation Bedroom light - Diagnose fault (light fitting, switch, wiring, or circuit) - Repair or replace faulty components as required Please include your licence number in your response

A qualified electrician required to: 1. Replace 4 pendants (see pictures) 2. Replace 1 lightbulb 3. Replace 1 switch board P.S the new pedants are still in boxes. Will need help to open them.

Need to replace 6 x down lights which have gone out. Bulbs will be provided but will need to bring ladder. Needs to be done this afternoon.

Hi there, I need a licensed electrician to replace a damaged wall power point (double GPO) in my home. One of the outlet holes is burnt/melted, so I’d like the full unit replaced and made safe.

Remove power point. A painter will do the patching and painting afterwards.

1. Upgrade oven Circuit to accommodate 2 oven (previous 1) 1.2. Install and fit off 2x oven in place. 3. Install and fit off range hood 4. Rough in 12v power feed for floating shelf for LED 5. Fit off and supply 2x stainless slimline GPOs for kitchen splashback (may be second visit with usb if possible) 6. Fit off all GPOs previously roughed in. 10 in total slimline. 3 with usb plugs 7. Swap light in bathroom to sensor in bathroom and add auto exhaust. 8. Safety cert

I need you to dig a trench that is 3.5m x 50cm for an electrician to run some cabling. Once the electrician runs the cables you will then need to backfill the trench.

Installing 1 new powerpoint socket in kitchen area. Double storey. Powerpoint access nearby, one behind the fridge to the right of the photo. Wall backs to laundry (see second photo) which also has power points on the same wall on the laundry side).

Have a number of switches that pertain to the backyard lights and the front yard lights. Also want to get fans automated. Need someone who is familiar with Shelly switches and can help me supply and install them. Approximately 8 light switches and 4 fan switches. This fee is for a consult for someone to come and then do the installation

We need a double power plug socket to be installed. There is a double plug other side of the wall so should be a straight forward outlet execution.

Hi, We are looking for a licensed electrician to upgrade an older ceramic fuse switchboard at a residential property in Malvern East (Melbourne). Scope of works to include: Assessment of the existing fuse board Upgrade to a modern switchboard with circuit breakers Installation of RCD safety switches (as required) Inspection of earthing/grounding and upgrade if necessary Compliance certificate on completion Please advise: Fixed price or estimate Whether an onsite inspection is required Availability Property access is flexible. Thanks!

I have a shed - I’d like the 2 existing Fluro lights removed and want 3 new double power points mounted high near the rafters. These are mainly for plug-in LED lighting and future flexibility.

Need a new Power point installed in the garage - closer to the top ceiling. Existing Power point nearby. Along the same wall. Devices it will power include CCTV accessories The wall is plasterboard

LG Aircon not working - flashing cooling light 5 times. E24AWN-NC11 Need it looked at ASAP

Replace 3x pendant lights, 2x outdoor flood lights and hide 1x tv cable. All lights have already been purchased and are ready for installation.

Whilst painting , I took the 4 gang switch out to paint around in the process 4 red wires popped out and now I dont know where they go. I put them back in where I though they could have come from but now different lights come on in different rooms some not at all .. All thats required is your expertise, it wouldnt be a hard problem to solve for someone who knows

I’m looking for a licensed electrician to replace two ceiling fixtures in my home. All fittings will be supplied by me. ⸻ 🛏️ Main Bedroom – Ceiling Fan with Light Replace existing ceiling fan/light combo with: Arlec 120cm White Chicago 4-Blade AC Ceiling Fan with Light (Bunnings product – supplied by me) Scope: • Remove existing ceiling fan/light • Install new fan/light combo • Ensure secure mounting and correct wiring • Test fan speeds and light operation ⸻ 🛋️ Lounge Room – Pendant Light Replace existing chain pendant light with: Schoolhouse Pendant Light – Chelsea (Fat Shack Vintage) (Supplied by me) Scope: • Remove existing pendant light • Install new pendant (chain style) • Adjust hanging height if required • Test and ensure safe operation ⸻ 🏠 Additional Info • Existing fittings are shown in the attached photos • Ceiling height is standard residential • No new wiring required (straight replacements) • Property is occupied and access is straightforward Looking to get this done soon Thursday the 18th or Friday the 19th of December.

need the pool heat pump connected. What’s already in place: • 32A breaker in the switchboard dedicated to the heat pump • 6mm cable already run from the breaker to the isolation switch • Isolation switch installed next to the pool equipment • Heat pump is in position Scope of work: • Open the isolation switch and confirm the 6mm feed is correctly terminated • Run the final connection from the isolation switch into the heat pump • Test the circuit to make sure it’s drawing correctly on the 32A breaker