Find experienced local tradies in Burwood NSW

I have a sign that needs to be fit on to a light board for both sides and a sign for the awning on top of the shop to display for the public

Patch and cement internal walls for painting - some render has broken due to be nailed etc - small job probably 10 sqm - most needing little done

Need drafting plans for enclosing a verandah for CDC approval.

Gyprock plaster to seal old chimney hole

We had 3 sinks removed in our office and need a plasterer to patch and repair the walls, see photos for more info

I need 2x gyprock walls patched and painted 1x render wall patched and painted I had a render wall repaired at this job earlier that needs to be painted. The holes are from old aircon controllers. They are roughly 100mmx100mm

Rendering. Renderer. Brick. Fence. Burwood

I would like approx a 3m wide built in wardrobe with frosted sliding doors which conveniently open up to 2x 450/460mm wide drawers and shelves, a centred 900mm shelf and 2x 600mm wide drawers and shelves with shelving on the side as pictured so I can put my microwave in it

Internal wall had a blow out when doing the control, need to fill and render the wall

bedroom wall needs rendering to achieve a smooth finish and eliminate the popcorn texture. The area covers approximately 9 sqm, and I will provide the render for this project. Needs 2 coats on ONE WALL!!!

Details Please supply and build 3 Built in wardrobes: Room 1 H 2.6m L2.5m Room2 H 2.6m L 2.0 m Room3 H 2.6m L 2.0m Price includes materials and labour and Airtasker fee

My restaurant’s kitchen has a glass wall where people can look in, I want to convert this wall to gyprock, so people can’t look in anymore . H: 1430 MM L: 1820 MM

There are two holes, one in the wall of a bedroom and a door. The size itself is about less than 10cm2. The paint is a plain white for the wall and a warmer white for the door would advise visiting to confirm the colour.

We need to demolish Only a new office room build with plasterboard and timber frame. stack up and leave debris onsite for removal by others Total wall area is about 17m2 or 1.7m3 max. , 1 timber doors and 1 windows which required savaged for resue. Office located on level 1 and access through a stair. Attached photo show the existing room.

New room for office in Burwood area. Total new wall area is about 70m2. Ceiling Heigh 2500mm. Scope: -Metal stud 600 centre and nogging, with 13mm plasterboard both sides, set finish. -Acoutic insulation batt between wall stud to partition wall between rooms only (Earthwool 11kg/m3 75x600x2700mm). No insulation to wall facing corridor -Budget Skirting -720 / 820 hollow doors (5 doors) -Protection during works and clean after works -no paint require Refer attached plan

There are two holes, one in the wall of a bedroom and a door. The size itself is about less than 10cm2. The paint is a plain white for the wall and a warmer white for the door would advise visiting to confirm the colour.

- Render the three faces/sides of the alfresco slab to a natural stone finish - render colour: very light grey to match top surface colour as close as possible

Have one set of IKEA wall hooks to be installed in my entryway in RED CIRCLE. It is drywall. I don't have the tools to check what's behind it It is for hanging jackets/coats, scarfs, umbrella, empty grocery bags You need to supply tools, studfinder and appropriate screws (countersunk) + anchors if needed

- remove remnant brick fence 1.0m (L)x 0.5m (H) x 0.3m (D), leave neighbour's pillar alone - cut/remove any protruding bricks - render the entire side of the damaged pillar with cement to create a smooth/flat finish

Timber slats removed from 3 walls, 1 x 4 metres and 2 x 3.2 metres and the cement render patched. Cornices will be installed at the top to cover most of the gap