Find experienced local carpenters in Potts Point

I have a small tallboy. It's flatpacked furniture, and the frame has fallen apart during moving. The Frame needs to be screwed together with proper screws to stabilise it (as the supplied screws etc arent holding it together). It's a 30 min job max for a carpenter with proper equipment.

Fix some dog scratches on 1 floor board and fix two corners of skirting board where puppy has chewed

Handyman / carpenter to assist with finishing off small renovation - general carpentry. Seeking help this week

Scope of Works – Kitchen Base Cabinet & Benchtop Replacement (Rental) Not custom • Remove and dispose of existing rotted base cabinet carcass and benchtop. • Supply and install standard flat-pack sink base cabinet (approx. 900mm wide) adjusted to fit 870mm opening.(Bunnings ) • Cabinet to be 600mm deep, white melamine interior, adjustable legs, securely fixed and levelled. • Reuse existing cabinet doors and handles; allow for hinge re-drilling if required. • Supply and install laminate benchtop with moisture-resistant substrate (33–38mm thick). • Sink cut-out edges to be fully sealed prior to sink installation. • Silicone sealing to sink perimeter and rear benchtop edge against tiles. • Licensed plumber to disconnect and reconnect sink waste, two taps, and spout. • Test plumbing and leave installation clean and fully operational.

I’m looking for an experienced professional to sand, stain and seal approximately 30 square metres of timber floorboards at a property in Potts Point. Details: • All areas are on the ground floor • Easy access • Looking for a neat, high-quality finish • Open to discussing stain colour and finish options Please include in your offer: • What’s included (repairs, gap filling, number of coats, drying time, etc.) • Your availability • Examples of similar work if possible Thanks, and I look forward to your quotes!

I have this vintage timber bench that needs some repair. The legs are wobbly - need stabilizing. Also, while the front of the bench is finished nicely with molding, the back side of it is exposed and rough. Can anything be done to tidy it up? I already have an upholsterer recovering it later - but I just need the frame fixed before that.

After an airtasker who can cut masonite and hardboard to size.Brad nails a bonus.

I would like the fridge to be built in to the kitchen by extending the white wooden panelling as photoed. Then the fridge door will be attached to the panelling door and they will open together. I am aware I might need to buy a different fridge. I need to do this before changing the surface of my kitchen.

Hi! I want someone to complete two jobs for me please. 1. Replace cupboard doors. I want to replace the doors of an existing large purple cupboard (due to the size, these will have to be truly bespoke, not from ikea/freedom, see photo, etc) with hinged wooden doors. I want bare wood / wood veneer, so the doors can be cut from scratch from wood rather than pre-purchased from an ikea / freedom. 2. create a small laundry cupboard around an existing washing machine.

take apart a small kitchenette (includes dealing with the plumbing/ sink / tap), remove ceiling hangers from concrete slab ceiling, take away rubbish.

Hi! I'm looking for someone to make a laundry and 1 wardrobe and put shelves etc into an existing pantry for me please. The laundry is a simple job - involves building a cupboard prior (or after) a laundry install. Approx dimensions 2100 H x 600 x 700. The wardrobe would be a mostly hanging wardrobe with drawers, installed along one wall, with approx dimensions of 470 D, 3200 W and 2200 H. I'm looking for a white finish with silver handles. The property is an old building, so looking for a classic finish (rather than modern). Something like the attached photo (those doors are from freedom). I settle on the property on 4 November, so I'd like the job to be completed that week please, prior to moving in. Thanks Catherine

Small carpentry tasks to finish renovation of flat in Potts Point - gap filling, laying a few floor boards around fire place etc

Need a quote and ideas from a carpenter to have book shelving made and installed and possibly a bookcase as a room divider.

We’re looking for an experienced carpenter to install a queen-sized wall bed (Murphy bed) that is currently disassembled. The bed was purchased second-hand and will need to be securely mounted. Scope of Work: - Create and install wooden framing to accommodate the wall alcove and ensure the bed is mounted to a flat, secure surface. - Assemble and mount the wall bed securely to the wall in line with safety and stability standards. Note: walls are made of brick (old 1920s building) Additional Info: - Location: 6th floor apartment (elevator access available for materials). - Access Window: Work must be completed between 8:00 AM and 4:00 PM, Monday to Friday (building regulations). - Materials: We’re happy to supply materials upon your advice, or you can provide them and include in your quote. Open to quotes — please include all labour, materials (if supplying), and GST.

Drill a hole in kitchen cabinetry to allow a power plug through and have it finished off with a ‘sleeve’

Hi Airtaskers, I am looking for a licenced and qualified carpenter to come install a wood panel onto the end of a kitchen cabinet. There are photos below that show the panel and the cabinet. I have the panel but you will need to bring the tools and possibly some plywood if you think you need to build up the centre part. I also need a solution on how we make the finish between the column and the wood panel neat - ideas welcome! (see photo two below). The wood panel is currently in three parts so there may be a bit of a jigsaw to get the coverage needed. Also, if you need to use nails that will be visible, please can they be *brass* coloured. Ideally I would like someone to help with this one morning this week or next week . Power tools can start at 8am so an 8am start would be great! Thanks!

Help a team of carpenters frame flat roof

4x low cabinets have been assembled, 1 more base 800x370 cabinet + fridge cabinet require assembly. I need the cabinets hung and levelled on wall. Feet also need to be installed. Must have laser level, packers + tools to complete job. Preference will be given to taskers who have experience with the Metod system. 🛠️

Timer skirting board quote

Task 1 - built IKEA kitchen cabinet including doors Task 2 - custom make and install kitchen shelves Task 3 - fix metal shelves (already made) in kitchen Task 5 - fix coat rack to wall Task 6 - fix push-press door openers to cupboards