Find a reliable appliance technician in VIC

I think it’s been over loaded and is unbalanced plus needs a service, I clean the filter and put a machine wash through it but something is still not right.

Revert capped gas insert so fireplace can be used.

We change to electric so need this gas cooker disconnected. It is still working so if you want you can get it, or take it away

The bottom edge banding on two overhead cabinet doors above the cooktop has warped from heat. The door faces are fine. I only want the bottom edges re edged. Do not quote to replace the doors. Scope; 1. Remove both doors, protect benchtop and splashback. 2. Cleanly cut back and remove the warped underside wrap only, leave the front face intact. 3. Prepare the underside edge, square, clean, and lightly sand for adhesion. 4. Supply and fit new plain white heat resistant ABS or PVC edge banding to the underside of both doors. Use hot melt or equivalent cabinet grade adhesive. No contact film. 5. Trim and flush both faces neatly, radius the arris lightly, seal the ends to prevent lifting, and clean any glue residue. 6. Reinstall and align the doors, check clearances to the rangehood and the neighbouring door, and confirm soft close works as before. 7. Leave the area clean Notes. • The repair is to the underside edges only. The colour can be plain white. A close white match is fine as the new edge is on the underside. • Bring 16 mm and 18 mm white edging so the job can be completed in one visit. Measure on site to confirm. • Location is an apartment kitchen near Camberwell Junction. Photos attached show the exact edges to be repaired. Onsite parking available. Requirements for the Tasker. • Cabinetmaker, shopfitter, or handyman with proven edge banding experience. • Provide a tax invoice if required. Please answer in your offer. Confirm you will re edge only, not replace the doors. Confirm you will use heat resistant ABS or PVC edging and cabinet grade hot melt or equivalent. Confirm your availability and parking needs.

Climb into roof (bring ladder) locate the source of smell and eliminate odour and/or the source.

I have a tilt garage and I want to make it automatic, with parts and installation

Security cameras installation dahua or hickvision 10-12 channels 6 camera 6 Mp , with flashing security light

Kogan washing machine is showing E03 error. I have tried draining the water and also checked the drainage pipe and could not find any problem there. The washing machine is “Kogan 10kg/6kg Washer Dryer Combo - KAGWAS10D6A” and the link to its manual is here : https://help.kogan.com/s/article/Kogan10kg6kgWasherDryerComboKAGWAS10D6AManualsandSupport

Pickuo washing machine from Hallam, delliver to Clyde North. - View all the details of this offer: https://www.airtasker.com/offers/01K8CRQ1JFP7WMWM46G63DJSKN

Smeg oven door taken off - strong springs to get pins back in. Need help with reattaching pins and placing door. Relatively quick job

My Haier washing machine / dryer combo doesn’t work and just flashes a wifi symbol. Preferably tonight Have tried to unplug and replug as well as click the temp+spin buttons to try get it out of that. I need this fixed ASAP

Hook up new Westinghouse gas hot plates

Our hot water isn’t working, pilot light went out a couple days ago in the wind we’ve started it again but there’s no running hot water but the gas is still working in the kitchen, just not the hot water? Help

Urgent leak at brass T or PEX press connection. Pipe details 16mm, AS417:8, AS2537, adapter DN16 x 2.2 CL2/10bar. This is the first pipe from the Zip unit and supplies the whole shop. Photo and short video attached. Details Inspect and locate exact source of leak Repair or replace leaking fitting and any damaged PEX or adapter DN16 x 2.2 CL2/10bar Isolate and test supply then confirm no leaks and clean up water Provide written quote and warranty on work and parts Location City store

I have purchased a garage remote for my roller door and gates. I am unable to program the new remote so need someone to come and do this.

Pick up an old large oven and range for scrap metal or parts and dispose of.

I have Arlo cameras installed on my property and I need to replace them with new cameras due to the old ones being nonfunctioning and out of surface warranty. I need four cameras just installed, which basically means putting in a couple of screws into the wall and mounting the cameras and plugging in into outlets. two cameras at the front and two at the back the only thing that you might need is clips for the cord not to hang but otherwise a drill and a ladder.

Westinghouse Easycare 500 washing machine not disposing of water from exit hose. Water building up and only being possible to release by lower exit release point. Nothing blocking the filter from what I can see when I open and release the water form the lower water exit point on the front. Looking to have this repaired asap

New oven purchased. Internal dimensions are slightly higher than old oven..need cabinet maker to remove oven base melamine and lowe by 5mm or som there is a drawer underneath that will require modification by the same amount

Wall connector install Require a licensed electrician that can provide an electrical compliance certificate afterwards. Refer to q&a below - if the price is too low, quote as needed - apologies for lack of knowledge in this area - happy to work through any further questions. Hadn't decided on in vs outside, or what's possible