Find a reliable appliance technician in Sydney Eastern Suburbs

We have bought an oven to replace an existing oven. The new oven is the same size as the old one and the measurements in the manual match so it should fit straight in the existing hole

LG model G8 455PL not cooling or freezing. Need assessed and fixed.

Dishwashing not draining. Likely a small blockage and an easy fix

Dishwasher drawer not working. Unsure why. Requires diagnosis and repair.

Collection of a washing machine and dryer and then helping move old one to carpark

Need a fridge technician to remove a rear light panel on my fisher and payel RF500QNX1 fridge. Can't work it out. Suspect there is mould growth after storing it for 2 weeks during renovations. Need to quickly clean it and put it back on

Maxi Pro Thumper massage machine is not working

Some of the igniters in my stove do not work. The gas comes through but the ‘click’ does not light.

My euromaid washing machine door will not close properly to start the machine. Something is going on with the latch

I have a bottoms mount freezer, 283 litre CHIq fridge that is compatible for a door reversal. There are 2 doors that require reversing. They swing to the left, I need them to swing to the right when facing the fridge

The Drip tray caught fire on Thursday 3 knobs burned off...think its salvageable. 6 years Old.

Just need someone to connect my washing machine to the drainage, water is already connected. Thanks

Need the rubber door replaced. I have the replacement part. Just need someone to come and do it.

Quick washing machine connection – need someone now I’ve just moved into a new apartment and need help connecting my washing machine to a cold-water-only supply. The machine currently has hot and cold inlet hoses. I just need someone strong enough/with the right tool to undo the hot inlet hose from the back of the machine, remove it and fit the blank cap/sealing washer as shown in the attached instructions. It’s a super basic job — I’m just not strong enough to loosen the fitting myself! Should take around 10 minutes. Please only respond if you’re local and available to come now.

Washing machine leaking – check connection & relocate if needed My washing machine is currently connected in the kitchen, however it is leaking from the hose/pipe and I’m concerned it may not have been hooked up correctly. Looking for someone experienced with washing machine installation/plumbing to: * Check the current hose and water/drain connections * Fix the leak and ensure the machine is connected safely and correctly * Assess whether the current kitchen connection is suitable * If the kitchen setup isn’t appropriate, potentially move and reconnect the washing machine in the bathroom, where there is also a washing machine connection Please bring any basic fittings/clamps that may be required. Happy to cover the cost of additional parts if needed. Timing: Tonight / Tomorrow

I have a brand new BBQ and need a licensed / certified plumber / gas fitter to connect it to a gas outlet right behind the BBQ (natural gas)

Kogan 10kg washer/dryer combo #KAGWAS10D6A Throwing error code E04. Something to do with water inlet or water sensor. Have checked filters and done a power cycle. Need fixed ASAP.

Dishwasher is not training. It’s a two drawer washing machine and the top drawer is not draining.

I'm hoping to get help & a quote for a job at our home in North Bondi involving an integrated dishwasher, kitchen cabinetry, and flooring. The issue: Our integrated dishwasher is boxed in by engineered oak flooring that was installed after the dishwasher was originally fitted. The floorboards now butt directly up against the appliance's base, with no gap or removable threshold, so the dishwasher cannot be rolled out for servicing or replacement. What we think the job involves: 1. Assess floor-to-underside-of-benchtop cavity height, and the depth/height of the recess the dishwasher currently sits in, to determine whether a standard, slimline, or other dishwasher will fit once the floor is corrected. 2. Cut back a section of the existing floorboards (ideally along board joints, in the direction of the plank run) to create enough clearance to remove the old dishwasher. 3. Disconnect and remove the existing dishwasher (plumbing/electrical disconnect maybe required) - i can organise if needed 4. Advise on and supply/fit a replacement dishwasher appropriate to the confirmed cavity height. 5. Reinstate the flooring around the new appliance, ideally with consideration for future serviceability (e.g. a scribe piece or similar) so this doesn't recur. 6. Reconnect plumbing/electrical and test. We'd like to avoid simply building a ramp of extra flooring up to the appliance, as we're concerned this could reduce clearance further and limit which dishwashers would fit, we'd rather address the underlying height mismatch properly. Could you let me know: - Whether this is something you can scope and manage (including any subcontractors needed for flooring/plumbing/electrical), or coordinate with in-house trades - Availability for a site visit to measure and assess - Rough cost range once you understand the scope - ignore what i have selected attached photos showing the current setup if useful. Thanks very much,

Asko washing machine Error 7 drain issue. A collapsible drain hose extension was used. Need to change it to a drain hose that is cut to length QUOTE MUST INCLUDE PARTS AND LABOUR