Find a reliable appliance technician in NSW

Moved into a new property and found that the taps for the washing machine are: 1) Not consistent 2) Hose does not screw all the way up on the cold tap 3) Water is leaking/sprouting out where the hose connects with the tap Seeking a licensed professional to offer either a workaround solution so that 3) no longer occurs - or a permanent fix so that both taps are consistent AND (cold water tap) no longer leaks

Need to replace the existing cooktop/oven with the improved second unit. When the existing unit is removed, the replacement oven/cooktop is to be installed in the same position. The cabinetry face panel will need to be carefully unscrewed to allow installation and then screwed securely back into place once complete. The existing cooktop/oven does not need to be removed from the property — it is simply being swapped with the improved unit already at the property. Please ensure the replacement unit is installed correctly, connected and tested, with both the oven and cooktop confirmed to be working properly before completion.

Fisher and paykel 8kg top load washing machine is constantly out of balance during the load - suspension rods may need to be checked or replaced

Haier Model: AWF80AN1 Issue: Showing E4 error after a few minutes. Initially water fills then stops and nothing happens. Doing a refresh cycle shows spinning but that's all. Tested the water pressure from tap, looks normal. Can't get around to the back of the washing machine since dryer is sitting on top and cannot lift it off.

Looking for someone to uninstall the current dishwasher and install a new one, along with connecting the drainage pipe.

- currently having indoor gas heating point near to the exit door. It is also stuck and I couldn't dismantle my heater. Very strange. Take it out and remove/dummy the existing line. - I need to move to the other side of the door as attached. - also attached how the incoming line in the other side of the wall in the attached image.

Brand new dishwasher in box. Westinghouse WSF6602XC 60cm freestanding dishwasher. Have space under sink - To RIGHT SIDE to fit in - power socket above dishwasher space/kitchen bench - on wall* *Will need to drill a hole in bench top to run power cord to socket on wall. BENCH TOP is, plastic laminate glued on top of a chipboard or particleboard. The dishwasher comes pre-fitted with the core connection lines: Water Inlet Hose: A 1.5-metre high-pressure hose featuring a 3/4" BSP female threaded connection (standard Australian garden-tap/mini-cistern size) with an integrated electronic AquaStop safety block valve at the tap end. Water Drain Hose: A 1.5-metre flexible ribbed grey drain hose with a rubber boot end ready to slide over a standard sink waste pipe spigot. I'll need to get the following from bunnings to allow for the installation job. Brasshards 2 Way Under Sink Valve 20mm x 15mm – Retrofit splitter that screws onto existing cold line to add a dedicated dishwasher tap. 3/4" BSP Male to 3/4" BSP Female Flexible Braided Hose (300mm–500mm) – Slim extension line to move the bulky AquaStop box away from the tight wall shelf. Kinetic 17 - 32mm Stainless Steel Hose Clamp – Metal clamp to tightly lock the grey drain hose onto the under-sink waste spigot. Thread Seal Teflon Tape – Essential for wrapping around bare brass threads to prevent leaks. You will need tools to fit all the above. You will need Spade Drill Bit or Hole Saw (approx. 32mm–40mm)to cut hole in sink wall and bench top/plastic laminate glued on top of a chipboard or particleboard. Let me know if I forgot anything? Thanks.

Collect dishwasher (h: 850 w: 595 d: 635) from bondi junction and deliver AND INSTALL to Bronte Rd

Need the rubber door replaced. I have the replacement part. Just need someone to come and do it.

Quick washing machine connection – need someone now I’ve just moved into a new apartment and need help connecting my washing machine to a cold-water-only supply. The machine currently has hot and cold inlet hoses. I just need someone strong enough/with the right tool to undo the hot inlet hose from the back of the machine, remove it and fit the blank cap/sealing washer as shown in the attached instructions. It’s a super basic job — I’m just not strong enough to loosen the fitting myself! Should take around 10 minutes. Please only respond if you’re local and available to come now.

Sorry I am being told multiple conflicting information from multiple companies so would like to see if the following is possible based on a recent suggestion from a company who looked at all our cables and breakers. They said we could safely hardwire our induction 4.6Kw to the existing 20A oven breaker and relocated our 2.3kw oven to a powerpoint nearby as the oven was originally a plug that got hardwired. Other circuit nearby is on 20A breaker. The existing oven cable is apparently a 2.5mm cable. It would be to hardwire AND install induction cooktop onto our bench (hole is already correct size) and add plug back to oven to connect to nearby powerpoint. May need a small hole drilled into the inside cupboard to get to the powerpoint but it is right next to the oven (length of cable may not be long enough to go into the existing hole at the top). Thanks If this is possible we’d like a quote on this. Thank you.

Need someone to connect my washing machine water inlet hose to the existing laundry tap. The existing tap/connector is heavily corroded and may need to be replaced. Please supply/install the appropriate washing machine tap or adaptor if required and ensure the connection is watertight. See attached photos. Licensed plumber preferred I’m not sure what the appropriate price is for this job, so please feel free to offer what you consider reasonable for the work required

Installation of brand new washing machine. Already in place in ground floor laundry but needs connecting and setting up

Help me: - disconnect one washing machine and move to the front porch - move new washing machine from store room and connect in laundry - move one sofa to front porch The old washing machine and sofa is free if you want to have it. Pickup location: Tempe NSW 2044, Australia Removals size: A few items Stairs: No

Move a rinnai gas heater from one unit to another safely. A plumber knows what a gas heater looks like

Need a new kitchen tap bought and installed so we can use Bench top DW and the taps

Washing machine leaking – check connection & relocate if needed My washing machine is currently connected in the kitchen, however it is leaking from the hose/pipe and I’m concerned it may not have been hooked up correctly. Looking for someone experienced with washing machine installation/plumbing to: * Check the current hose and water/drain connections * Fix the leak and ensure the machine is connected safely and correctly * Assess whether the current kitchen connection is suitable * If the kitchen setup isn’t appropriate, potentially move and reconnect the washing machine in the bathroom, where there is also a washing machine connection Please bring any basic fittings/clamps that may be required. Happy to cover the cost of additional parts if needed. Timing: Tonight / Tomorrow

I have a brand new BBQ and need a licensed / certified plumber / gas fitter to connect it to a gas outlet right behind the BBQ (natural gas)

Smeg dishwasher filling up with water at the bottom and also sometimes getting stuck on a cycle and unable to reset.

Need a new seal installed on my LG washing machine