Find experienced local tradies in Central London

Need a qualified electrician to connect a 4.5kW sauna heater (BC45, 230V single phase) to an existing dedicated sauna circuit. Most of the heavy lifting has already been done by a previous electrician - the circuit is already installed and live in the consumer unit (B32 MCB on its own breaker labelled “SAUNA”), cable has been run from the board to the sauna room, and a Contactum rotary isolator switch is already mounted on the wall. The issue is the previous electrician hardwired the infrared sauna panels but didn’t connect the main stone heater, which has its own separate cable with crimped terminals that needs wiring in. The heater is already in position and ready to go - it just needs connecting to the existing circuit, either into the isolator or junction box that’s already there. Photos attached show the existing isolator and cable run, the consumer unit with the dedicated sauna breaker, the heater’s cable/terminals, and the heater unit itself. Happy to discuss on-site but it should be a relatively quick job given everything is already in place.

electric gibus awning / line not moving. need to programme a new Somfy Smoove and make sure everything connected to power it so it can move in and out again. This job is to site visit, to supply and programme a new somfy smoove. Any further work to be agreed and charged on top

We are a sauna operator in North London. One of our sauna doors has a timber frame with large glass panel. We are struggling to get it closed and sealing in the heat. We would like someone (a door specialist) to come in and assess and adjust the door - thank you

Site visit to review our electric awning

Need a qualified electrician to hardwire a new Insignia MXOS1700 hybrid sauna inside my home. This is a hardwire-only unit - it has no plug and must be permanently wired to a dedicated circuit from the consumer unit. It's an outdoor-rated model being installed indoors so no external cable runs needed. Electrical Specs (from manufacturer manual): Harvia 4kW stove - 240V single phase 4 x far infrared heaters - 1,320W total (240V single phase) LED lighting, Bluetooth, control panel - 120W (240V single phase) Total load: 5,792W / 24.2 amps 240V single phase only - no three-phase or supply upgrade needed Requires dedicated 32A MCB and 6mm² T&E cable minimum (depending on run length) Scope of Work: Survey cable route from consumer unit to sauna location inside the property Install dedicated 32A MCB in consumer unit (spare way needed - can send photos of fuse board in advance) Run Twin & Earth cable from consumer unit to sauna Install local isolation switch near sauna Make final hardwire connection at sauna's electrical junction box Test, certify, and issue Electrical Installation Certificate (Part P compliant, BS 7671 18th Edition) I have the full Insignia installation manual and Harvia wiring diagram available on the day. Timing: Must arrive by 12pm Friday. Estimated job duration 1.5-3 hours. Note on cable run: The sauna is on the first floor, directly above the consumer unit on the ground floor. They share the same wall, so the cable run should be very short and straightforward - essentially straight up one level.

I have had some issues with damp at my property due to issues with an external render.  I am looking to render one external wall (ground floor) at my property to avoid moisture coming inside.  There are cracks in the render and it measured high in moisture in many places. There was previously a lean to shed which has now been removed.  Instructions are: remove the render back to the brickwork. Treat the bricks with three coats of Cementone Aquapruf then render the wall with a moisture inhibitor in the moisture mix. Ensure that the new render ends above ground level in a bell mouth drip. 

Sanding walls and architrave and doors and some minor filler work. Must have 225mm drywall sander. If not please don't offer

fix a retractable electric gibbus awning

We have an array of IKEA Pax wardrobes in a dressing room. We would like these moved to a new room and a carpenter to build around them. Design to be agreed but I’d like the finish to be similar to the attached photo.

I have a terrace wall that needs silicon rendering. The wall is 5.8 meters long by 1.5 meters high at its max height. There is also a small wall area which is 0.45 meter high and 2.5 meter long

I'm looking for some floor to ceiling wardrobes to be built for the bedroom

I have a buggy with two broken metal tubes near the back wheels. I need a quick, solid repair to get it moving again.

I need this hole in my drywall fixed, and the tiles re-fitted. I'd estimate the entire area that would need to be cut out between studs is around 80cm in width and 75cm in height. I still have the tiles that have come off and they aren't damaged. Aside from the tiles which I already have, I'd need the materials to be provided as part of the job. There is free parking in a carpark at the front of the building, however, the vehicle would need to be able to fit under an archway, smaller vans do fit through but a large van wouldn't fit.

Hi there! I'm looking for help with the following: 1. Removal of the pictured built in wardrobe, including cleanup of walls from wardrobe removal. 2. Relaying of laminate flooring from where wardrobe was. I have spare materials from when floor was laid that is enough for this small section of floor. 3. Planing of 2-3 doors, previous workman did not return to complete this part of laying the floor. 4. Secure door profile for bathroom door - also outstanding from floor laying. 5. Complete front door step laminate floor laying - also outstanding from incomplete floor laying. 6. Full disposal of all waste from project (wardrobe, leftover flooring) Thank you in advance.

There is a about a 12cm section of drywall that has come off. I have applied polyfilla to it but it will likely need another layer and to be sanded and painted. I will provide the paint, you will need to bring your own tools

Need to remove a three doors built in wardrobe in one of the rooms. Then I want the walls and roof affected by the removal to be left like if there never was a wardrobe in there. Need the debris to be taken away as well.

To spray and resurface bath's enamel. Complete a repair of the damaged wooden balcony ledge which has changed colour and vanish or seal it. Marble and natural stone restoring

Bulid a makeshift wardrobe against a wall

We have a small built in wardrobe that needs fixing looking for an experienced handyman or carpenter to, Remove existing hanging rail Patch/fill any holes and make good Install a new solid timber shelf at the top Install a new hanging rail (possibly double hanging – open to advice) Install open shoe shelf at the bottom I can supply inspiration photos. Happy for you to advise on best layout for space saving. Happy to either supply materials myself or reimburse, please advise. Requirements Experience with wardrobes or cabinetry Own tools Neat finish. Please get in touch. Not urgent but would like it done soon.

Old Mitsubishi car (2004), passenger door needs to be taken off, metal/steel plate needs to be welded on, door put back and attached to the metal/steel plate. It doesn’t need to be beautiful but I think you need a gas welder for this kind of work. We have had this work done already in the driver side - please see picture.