Hire a reliable appliance service in London

Descale and fix Sage Barista Pro espresso machine The machine has stopped moving water entirely due to severe limescale build-up. It won’t run a coffee cycle or a descale cycle. Need someone to descale the machine and clear the internal blockage. The machine may need to be partially disassembled to access and clear the pipes or inspect the pump. Model is the Sage Barista Pro SES878. Located in Archway, north London. Please only apply if you have experience with espresso machine repair or descaling.

THE HOSE HAVE A HOLE NEARLEY the gun

I do not know I started the machine , came to check an hour later and the sink was flooded also the floor. Shut down the machine. Tried to re activate it to drain the water and take out my clothes, the machine is not responding

I think it blocked somewhere it’s not draining

Washing machine seal replacement

Disconnect and remove a washing machine. 3rd Floor flat with lift access to basement car park..

Hotpoint fridge freezer has been flashing and beeping non stop for hours, both are off and we need it fixed today

Due to an injury I have not been able to defrost the two shelf freezer in our freestanding fridge freezer for one year. It’s still closes and works but the ice and Frost has built up significantly and requires somebody able (i.e. has two hands which I currently don’t have the use of.) to defrost and then gently clean with our cleaning materials to wipe up frozen spills etc. It cannot have boiling water or metallic tools or scrapers. We have extremely hard wooden and plastic tools that you are welcome to use.

Hi, I need a kitchen a worktop replaced with new worktop, cut to size and cut to fit cooker hob. If you can install the hob also that would be great

Fishy smell from oven. Someone from Domex has come round to look at the oven. He said the oven works completely fine. He said he did note the fishy smell and said it could point to an issue with the main electrics but not the oven itself. He recommended for an electrician to come round and take a look at the electrics properly to make sure there isn’t a potentially dangerous fault.

Dishwasher is not draining propoerly, and control panel is glitchy. Sometimes it lets you choose a setting and runs normally, but most of the time it rejects and glitches when you choose a mode, and so it’s hard to get started

Hi, I need someone to remove a broken integrated washing machine and prepare the space for a replacement freestanding washing machine. The existing machine is an integrated Candy washing machine fitted under the kitchen worktop. Appliance installers have advised that they cannot remove the integrated unit themselves and have asked me to arrange this before they can install the new machine. The job would include: • Disconnecting and removing the existing integrated washing machine. • Checking the clearance under the worktop and removing or adjusting any trim, panel, bracket, or fitting above the machine if required to allow a standard freestanding washing machine to fit. • Taking away and disposing of the old machine. • Leaving the water, waste, and electrical connections ready for the new appliance installer. I can provide photos of the current setup below. Please let me know if this is something you can do and provide a quote if possible. Thank you.

We need to replace the rear wheel break side of the yoyo babyzen stroller, we've taken the old wheel off but can't attach the new wheel

My Hotpoint washing machine has f05 showing and it’s not draining. I need it fixed today is possible, please.

I’ve got a new washing machine which needs to be installed. The old one is still here and is hard wired into the wall rather than a plug and would require the same with the new washing machine

I have had running to my hob and oven and just want this capped off as I don't need it anymore Cheers Let me know if you want to come and see first

Install a dishwasher, dishwasher is slightly further away but I have bought the necessary tubes needed included in pics. Tubes will go under cabinet and then link to adjacent dishwasher. Should be fairly straightforward.

Electrician to install new Electric Cooker

Secondhand bed frame, largely assembled, but some of the larger screws won't go in further using hand screwdriver; power tool needed to get them fixed properly

Looking for a plumber to install a proper cold water feed valve for a washing machine. There is an existing cold water pipe in place, but it does not currently have a standard threaded outlet suitable for a washing machine hose. The job is to fit a suitable isolation valve with a 3/4" threaded connection. The waste pipe is already in place. Access is straightforward (see photo).