Find experienced local tradies in Wahroonga

Close off an existing internal opening with a non-load-bearing stud wall. Approx. one large doorway/opening as shown in photos. Requirements: – Timber stud framing – Acoustic insulation (e.g. Bradford SoundScreen or equivalent) – 13mm acoustic plasterboard on both sides – Acoustic sealing around perimeter – Set and sand ready for painting – Please minimise damage to existing tiles and opening, as the wall may be removed in future – Please quote labour + materials Please provide photos of similar stud wall / plasterboard work you have completed.

I'd like a wall 2.9m long and 2m high installed in my garage. doesnt need to be perfect, just as a screen. It will need a door, much like a ceiling man hole so i can go through the wall. Non load bearing, just for looks, 10mm gyprock is fine, no electrican work, no painting, no skirting.

I need a timber stair balustrade removed carefully. The job includes: * Remove the entire timber balustrade (vertical posts and top rail) shown in the photos. * Remove fixings (screws/bolts/nails) where possible. * Minimise damage to the existing timber capping and surrounding walls. * Stack all removed timber neatly (or dispose of it if agreed). The balustrade is approximately 2–2.5 metres long. Important * I believe this is not structural, but please inspect before commencing. * If you believe it provides structural support, stop work and discuss before proceeding. * Care is more important than speed. * Please bring your own tools (multi-tool, pry bars, drill/impact driver, etc.). Preferred experience * Carpenter * Handyman experienced with timber balustrades * Cabinet maker also suitable Questions for Taskers 1. Have you removed similar balustrades before? 2. Will you minimise damage to the timber capping? 3. Can you dispose of the timber if required? 4. Approximately how long do you expect the job to take?

Require a painter to patch and paint this hole.

I have just purchased an 85 inch Sony Bravia TV. I want it installed on the plasterboard wall, ideally with cables hidden.

Description: I need a ceiling skylight (perspex/light panel) fully covered and closed off using gyprock. * Located above a stair void (double-height, difficult access) * Skylight currently lets light through — I want it completely sealed and finished as a normal ceiling * Area is visible, so finish needs to be clean and professional Scope of work: * Remove or cover existing skylight panel (advise best approach) * Frame as needed to support gyprock * Install gyprock to close off opening * Full plastering, setting, sanding * Paint to match existing ceiling * Ensure smooth, seamless finish with surrounding ceiling Access considerations: * Located directly above stairs → ladder/scaffold setup required * Tasker must bring appropriate equipment for safe access Requirements: * Experienced gyprocker/plasterer (carpentry skills a plus) * Must bring all tools and materials * Clean finish expected (no visible joins) Budget: * Expecting around $500 (hearing offers), depending on access setup and complexity * Open to quotes if additional work required (e.g. framing), but explain upfront Timing: Flexible, ideally within the next 1–2 weeks Photos attached for reference

Need to install two power points

Gyprock very small wall cracks beans

Remove old switches and plugs, supply and replace with Clipsal Iconic series. Majority are single gang switches and double plugs. No precise budget, best price from qualified and insured supplier.

Small Gyprock hole repair. Size of a tennis ball.

Remove and replace plaster board (approx 7.5m x 1.2m). Cornices at the front will need a generic replacement. Three coats of paint to new plasterboard

Need a cement renderer to fix some bathroom walls. Approx 8sqm total

I have a small hole, smaller then 10cm, on a gyprock wall that needs repairing

Damaged area of brick fence requires rendering and painting to be matching with surrounding area.

A few new power points in bedrooms one on ceiling .. change outlets to allow booster for internet

Just needing someone to make an outdoor power point to connect various things to.

Rendering of brick wall, approximately 17 meters in length, 600mm high, stepped. Will also include a small amount of brickwork on one side pillar- cutting approximately 500mm of brick and rebuilding in double brick

Need brick strips next to door to be rendered. Requires both corners and strips built up to match current door frame . Approx 3-5mm cover on left side and approx 12-15mm cover on right side. 2.1m height and about 110mm depth. Finish smooth for painting. Need to include for materials.

Hole in window cornice when trying to install curtain rod - approx 700x700mm

Power not working in kitchen power points. Elsewhere is fine. Can't find issue at power board.