Find professional local plasterers in Wahroonga

We need 2 x walls in garage to be gyprock, skirting at bottom and edging on top. As we are keeping ceiling with clear polycarbonate. So we need neat finish

Remove two wall mounted tv frames from wall, plaster over if required and patch paint to cover. Paint one unpainted (raw timber) 7m skirting board in white (byo paint and paint brush).

Install supplied gyprock sheet to a hole in ceiling, inside a cupboard. No need to paint or sand.

Close off an existing internal opening with a non-load-bearing stud wall. Approx. one large doorway/opening as shown in photos. Requirements: – Timber stud framing – Acoustic insulation (e.g. Bradford SoundScreen or equivalent) – 13mm acoustic plasterboard on both sides – Acoustic sealing around perimeter – Set and sand ready for painting – Please minimise damage to existing tiles and opening, as the wall may be removed in future – Please quote labour + materials Please provide photos of similar stud wall / plasterboard work you have completed.

I'd like a wall 2.9m long and 2m high installed in my garage. doesnt need to be perfect, just as a screen. It will need a door, much like a ceiling man hole so i can go through the wall. Non load bearing, just for looks, 10mm gyprock is fine, no electrican work, no painting, no skirting.

Require a painter to patch and paint this hole.

Job description Scrape back the water affected section on the cornices Re plaster the scraped cornices areas Apply one coat of high opacity stain blocker to the stained areas Apply one coat of sealer to the new plasterwork Apply two coats of ceiling paint

I have just purchased an 85 inch Sony Bravia TV. I want it installed on the plasterboard wall, ideally with cables hidden.

Description: I need a ceiling skylight (perspex/light panel) fully covered and closed off using gyprock. * Located above a stair void (double-height, difficult access) * Skylight currently lets light through — I want it completely sealed and finished as a normal ceiling * Area is visible, so finish needs to be clean and professional Scope of work: * Remove or cover existing skylight panel (advise best approach) * Frame as needed to support gyprock * Install gyprock to close off opening * Full plastering, setting, sanding * Paint to match existing ceiling * Ensure smooth, seamless finish with surrounding ceiling Access considerations: * Located directly above stairs → ladder/scaffold setup required * Tasker must bring appropriate equipment for safe access Requirements: * Experienced gyprocker/plasterer (carpentry skills a plus) * Must bring all tools and materials * Clean finish expected (no visible joins) Budget: * Expecting around $500 (hearing offers), depending on access setup and complexity * Open to quotes if additional work required (e.g. framing), but explain upfront Timing: Flexible, ideally within the next 1–2 weeks Photos attached for reference

Gyprock very small wall cracks beans

TWO 65cm x 55cm skylights will be closed with new colorbond roof. I need remediation work to the ceiling including removing skylight chute and gyprock/plaster ceiling flat, ready for painting. Also need to patch up ceiling near skylight that has water damage.Painting is not required for this job

Need cove cornice removed from house 90mm and square sent ready for paint Two storey 4 bedroom house No bathroom

Replaster a hole in the wall

Small Gyprock hole repair. Size of a tennis ball.

Remove and replace plaster board (approx 7.5m x 1.2m). Cornices at the front will need a generic replacement. Three coats of paint to new plasterboard

I have a small hole, smaller then 10cm, on a gyprock wall that needs repairing

Hi there. Need a 40cm diameter hole in my kitchen ceiling to be patched and plastered up. No need to paint. Ground floor and easy access through manhole in the kitchen ceiling. Will supply ladder and floor and surface coverings.

Hole in window cornice when trying to install curtain rod - approx 700x700mm

old ceiling needs re-plaster in one bedroom approx 3m x 4m. New cornices probably required too.

I installed a eket cabinet (details in picture)into the drywall. However was unable to successfully install one of the wall brackets and is now uneven. Need help even it out. Also I have a table I would like to custom cut for it to be at the top of the cabinet (1770x360). Any further questions please ask. It is a drywall and studs.