Find experienced local tradies in Inner South West Sydney

Hi I need a ceiling light installed, currently have oyster light, and 3 power points. Please ignore price I have listed as I’m not sure how much

One glass panel in my staircase balustrade has cracked and needs replacing. The metal frame is intact — only the glass panel needs to be supplied and installed. Looking for someone experienced with glass or balustrade repairs. The panel appears to be tempered/tinted safety glass. Access is easy and the panel can be measured on site.

I need someone to patch a hole in the plasterboard. I have a patch kit and filler, you will need tools. No followup for sanding/painting required. I also need help mounting a wooden board on the wall above a doorframe. You will need a saw, tools, and screws suitable for mounting into wooden studs.

Looking for someone to execute curved wall as per plans and gyprock 2 concealed doors

Have the glass balustrade just need it installed please

There are three holes in the ceiling after fan installation. I have one wall which needs refinishing as has been damaged with sticker removal

Handyman to assist trades people for various tasks and cleaning up. 8 hours max

Our built in microwave/oven has died. When I pulled it out I realized that it's hard wired in. The microwave replacing it requires a power point. I need help unwiring the old microwave/oven combo and installing a power point so I can use the new device.

I need a renderer to repair some cracks and damage for a remedial project.

build 2 gyprock walls and frames with sound insulation, including cornices and skirting boards and sanding ready for painting 1st is 4.35m length x 3 m high and put in a standard sized door frame and door 2nd is 3.6m length x 2.8m high - no door on this wall

I need to install 6 new power points supplied by me in new locations in the house, also install LED mirror in the lounge on wall, it's heavy needs 2 people to carry.

Small but precise ceiling plaster repair in a 1960s home being prepared for sale. This needs someone with genuine plastering experience. The original skim coat on a bedroom ceiling has delaminated from the plasterboard sheet underneath. Affected area is approximately 500mm long. I've already scraped back all loose material to a firm edge and confirmed the plasterboard sheet underneath is in solid condition — no moisture damage, no structural issues. The delaminated material is 1.1–1.3mm thick, consistent with the original finishing skim. Need someone to re-skim the exposed area with appropriate setting compound, feathered out to blend invisibly with the surrounding ceiling. The ceiling will be professionally painted afterwards so the finish needs to be seamless — this is for a sale, not a rental patch job. When you make an offer, please include: What compound/product you'd use Your availability in the next 1–2 weeks

Need a renderer to skim coat flaked off render. Have three bags of skim coat and render ready to go. Sponge float.

I need a professional to securely mount an IKEA Stockholm 2025 mirror (90x90cm) on a Gyprock/plasterboard wall. The mirror weighs approximately 13.5kg and has a built-in shelf, so it must be perfectly level and structurally sound. Scope of Work: Assessment: Identify if studs are available at the desired location. Installation: Securely hang the mirror using appropriate heavy-duty fixings. If no studs are available, you must use metal toggle bolts or hollow wall anchors (Molly bolts) rated for at least 20kg. Precision: Ensure the mirror is 100% level (the shelf makes any tilt very obvious). Safety: The installation must be flush and secure enough to handle the weight of the mirror plus items placed on its shelf. Requirements: Experience: Proven experience hanging heavy mirrors or artwork on hollow walls. Insurance: Must have active Public Liability Insurance. Tools: Please bring your own stud finder, spirit level, drill, and heavy-duty hollow wall anchors (unless you specify otherwise).

Adjust the awning as it is currently sitting crooked. The Arms needs adjusting in order for it to sit straight when fully extended.

I would like an experienced carpenter/builder to rebuild the lower section of a gyprock wall (laundry) where moisture has caused the timber bottom plate and bottom of studs to rot & crumble away. In 2-5 years, I would like to rebuild this entire room (as understand the issue is bigger than this one wall!), but for now, would simply like the wall made structurally sound and rotten material replaced with moisture-resistant alternatives to buy me some time before I plan a bigger renovation. Will need to make the studs structurally sound (add something to support them at the bottom as no longer touching concrete base), add new bottom plate (something moisture-resistant please), and replace the missing gyprock & door framing. I've removed lots of the damaged materials so you can clearly see the issue!

Reattach a damaged aluminium awning above a door will require a ladder, if unable to attach simply remove from the wall

I’m looking for an experienced handyman / plasterer / painter to complete the following work: 1. 2 walls to Drywall / plasterboard patch • Area to be sheeted and finished: 700mm (W) x 2480mm (H) - 1 photo attached • Includes fixing plasterboard, taping, setting, sanding, and blending smoothly with the existing wall. You will supply materials for drywall. • Must be paint-ready finish 2. Drywall 2nd room full wall. See photo attached Requirements: • Experience with plastering and painting • Clean, tidy workmanship

fix 3 spots where the ceiling cornices are damaged. One has been smashed, this is the photo where it has been taped over in white. The other two are existing cuts were previous built in wardrobes were taken out and replaced with new ones. Render one air vent that has been bricked in. White set tender finish this. Then render in gabs in brickwork in small hallway. It can still look like brick/textured but needs to be flat to make it easier to paint.

I need a 5m built in wardrobe done in the granny flat. Location is in Lugarno NSW