34 Plasterers in South Yarra

Plaster board repair with some kind of socket sticking out. Best solution at fixing This.

Need a hole filled in professionally

Plasterer required to stop-up a small room extension in South Yarra. The room size is 2.4m x 2.1m with a ceiling height ranging from 2.4m - 2.1m (raked ceiling) Scope of works Allow to stopup all wall and ceiling recessed joints. Allow for internal and external corners. Allow for one skylight shaft to be finished with a level 5 finish. Allow for two bulkheads to be stopped up. Allow for sanding on completion. Allow for one small repair to existing ceiling (See photo) All plaster sheets are hung. All materials are supplied by builder (base, top coat, angles, beads etc.) Must have own tools and skills to complete the job.

A 2 metre by 2 metre area in kitchen, and 4 small light fitting holes.

Small patch of dry wall paint came off after taking out 3M sticker for hanging wall items. Drywall paint came off, repair will need to take a plaster no more than 3cmx3cm to ensure patch is covered and looking as new.

We have a wall with a 100mm “step” in it which needs to be made flush. Job is to batten out the existing wall and install plasterboard to align with existing bulkhead size 1630mm by 100mm by 2700mm. Pelmets above existing windows to remain as is. Remove ceiling vents and extend ceiling to adjoin wall - square set. Reinstall ceiling vents aligned to new wall alignment. Note: vents are stand alone and not connected to any ducting system. Disconnect and reposition power point, light switch and internet outlet following wall modification. Supply and install new skirting board to new plasterwork to match existing (pvc) Plasterwork to be finished in preparation for painting (painting by others).

2no. Timber stud lathe and plaster walls to be demolished each 1m wide and 3.5m high. Reinstall these to the same width but in a different plan position approx 250m back. Retaining and reattaching the cornices. Must provide all tools/materials/ plaster disposal and clean up after works.

I need a hole fixed In plasterbaord , will provide all materials and pay for some one to fix it

Just need one sheet hung. Please msg with quote. Flexible with time in the next week. I have the plaster on site, beads if need. There was water damaged which we have cut out

As per photo and description.

Require hole in wall to be patched on Monday the 15th of September. Needs to be a smooth finish, but doesn't need to be exact colour matched as we have painters coming in.

I need someone to plaster and paint the little patches on the corner of the wall. And maybe paint the little patch on the skirting as well. Patches are pretty small. Need this task completed by Saturday evening as I’m moving out Saturday . Thanks :)

We have cut through a small space between kitchen and living area. The hole needs sling good on the sides and the kitchen side has an existing chunk of render missing which was behind an old cabinet. Property is 1930s, exposed bricks are sound, old render is quite thick. Looking for a rounded finish of possible but not essential (see existing doorway). Thanks

To fix 2 holes in a wall , one has a socket sticking out, also to paint section of wall..

Need a hole filled in professionally, sanded and paint colour matched.

Plastering a small hole in the wall and mounting a dryer with brackets that need securing onto wall.

Fell into the wall and cracked a hole in the plaster wall

need a plasterer/ finisher to trowel our 2 projects for us. we have / will be hanging all the plaster, and need a qualified trade to come in and base/ top and sand the walls and ceiling. one is in beaumaris and one is in hawksburn

Hello there - have a gutter on my balcony which may need to have a metal flashing put in and then I need to repair the plastering underneath where I have had leakage... plastering probably at various points in a 2m x 3m space In south Yarra - good for you to come anytime you like to have a look and either do it or quote..

Renovating a house and need 10 sections of 55mm curved cove cornice cut to fit for ceiling. Need to measure and cut onsite as angles are all different. I have cornice and drop saw