Find a professional mdf contractor near you

Looking for someone to come and cut a couple MDF panel (2400x1200x3mm) into strips of 50mm for kitchen Reno. I will need you to double check the dimensions you need to cut ready and electricity available for use. Please let me know if you can help with transportation of the boards too

I have popcorn ceilings throughout the apartment and I want it covered with Easycraft® easyVJ100 General Purpose 9mm 2400 x 1200mm MR MDF E0 Primed White or similar. It is not in the bathroom and laundry areas. I am moving in around this date so the apartment won’t have a lot of furniture etc. Preference date is Monday 16th, or Tuesday 17th November. Need guidance over process and timeframe. Thanks!

Need a carpenter to install MDF pre Primed Sheets to inside Walls asap 9mm

Hi, I’m looking for someone experienced to securely mount 3 MDF slatwall panels onto a wall， 38kg per panel. I’ll be there for helping. The panels will be used to hang products for display. Only one panel needs to be cut shorter to fit the wall. Could you please provide a quote for installing each panel or a total quote for installing all four panels? Please find the panel specifications here: https://www.dinyashopfittings.com.au/products/charcoal-matte-landscape-slatwall/ Please bring all necessary tools, including suitable cutting equipment. Thanks!

1.6m x 1.2 m mdf board needs to be installed onto a gyprock wall. I want concealed fix. I have wood strips. Example pic as shown

We have a tin covering on a wall that has been chased to allow electrical wires to run behind. We want a 5mm MDF panel to be cut and attached to the tin (glue). It can have some joins. 2 sides will need fine cuts to match the existing trim. The MDF needs to cover the whole wall - from top of skirting to the ceiling. Looking for a neat job. Take all waste with you.

I need MDF filler panels cut to size. There are 3 filler panels of 720mm length to be cut into 6 pieces (2 from each panel). And one panel of 2058mm to be trimmed to size length wise to 51mm width. Requires a table saw or CNC cutting.

Looking for someone to install MDF wall cladding/panelling in my hallway and living area paint them in white similar to the attached photo. Please quote for supply and installation, or labour only if materials are separate. Must have experience and provide photos of previous work. Located in Rowville

Hello, we have around 750bins that we need to install with MDF boards. MDF Boards are already on-site. We just need a team to finish installing them. You'll have to secure the screw you'll use for this project as well as the scissor lifts.

Need kickboard and spacers cut for cabinet install. I have the MDF at the correct lengths and depth (18mm). It needs to be cut for the correct widths. The MDF has already been 2pac poly painted. Cut 1: 40mm (length at 884mm) Cut 2: 16mm (length at 884mm) Cut 3: 84mm (length at 1199mm) Cut 4: 84mm (length at 1199mm) Cut 1 & 2 from a single piece of MDF (width: 140mm) . Cut 3 & 4 from separate pieces of MDF.l (width: 120mm) Need carpenter or cabinet maker with a table saw or track saw at workshop to make straight, clean cuts to also keep paintwork in tact. Looking for someone local to Banora Point where I can drop and pickup the MDF. You can also pickup and drop off if you would like.

Cut a 2m MDF hardwood piece of panel down to 135cm.

Need to install fluted mdf wall cladding- please see pic attached. Around 8.7 meters divided in three walls . I will supply the cladding materials. Located in Williams Landing

Install vent cover over th stove

I have 3 pieces of mdf boarding that need to be cut. Two require holes for power points and one straight cuts for end pieces.

I have the mdf panels, need them cut & cup hinge holes drilled to replace existing doors & drawers. (9 doors, 4 drawers)

We have a vanity with some damage. Looking for option to repair or cover to make cosmetically look good. Dimensions approx 715 x 472 Thanks Adam

I used to get my MDF sheets cut to size at Bunnings, but they no longer cut MDF in their Cut Shop. A single 2440x1220x3mm mdf sheet can be cut into 48 sheets that are approximately 200x300x3mm, I need that done so I have pieces that are small enough to fit into my laser cutter. I don't have a saw or any of the tools necessary to do this. Bunnings used to charge $1 per cut after the first, which in this case would have been 3 cuts on one axis, then 11 cuts on the other (stacking the 4 long sheets and cutting them together). I don't mind paying $20 per sheet that is cut down this way, and if I've got someone who can do it, I would like to cut probably 5 sheets worth so I've got a supply for a while.

I need the gap on the left hand side of my garage filled the mdf paneling I have bought. The gap is 2.35m high and 0.71m wide. I have bought 2 panels that are 1.2m high and 0.9m wide. The paneling will need to be cut to size and be secured in place. I don’t have any fittings or fixings so this will need to be procured once you assess the task. There is also a few items to consider at the top of the gap when installing this. They are in the picture. I will obviously pay for any fittings or fixings required on top of the fee to you. You will need to supply your own tools.

We have some MDF planks for kitchen trimming that need to be trimmed as they are too wide (only 4 meters worth). I don’t have the tools to cut it straight so keen to have someone cut it for us.

Check the attached file for the scope of work please.