Find a professional internal door contractor in VIC

I need my internal bathroom door to be replaced. I need the new door to be supplied and installed and old excising door to be disposed.

1. Hang a new door with the door handle (door size 2340*720), door jhamb already installed. 2. Adjust the front door and powder room door 3. Install a door handle to master ensuite door 4. Install a prebuilt manhole, plaster already cut and manhole from bunnings will be provided. Door, door handles, prebuilt manhole and hinges will be provided

I have an internal door that I cannot install into the door frame and need someone to do this - the door is the right size

Need an internal door hung - new handles, hinges supplied

I’m looking to have damage to internal bedroom door repaired, as shown in the attached photos. The job will involve: - Patching and filling the hole and cracks on door. -Sanding the repaired areas smooth and applying primer. -Colour-matching the existing paint and finish. I don’t have any tools, materials or paint, so please supply everything required for the job. Your quote should include all labour, materials and supplies. I’m looking for a neat, durable, professional-quality repair, with the patched areas blending seamlessly into the existing door finish. Please include your total quote and availability to complete the work.

Hi, I need two small holes repaired in two internal wooden doors. I’m looking for a simple, tidy repair. It doesn’t need to be perfect, but the holes should be filled and the finish should blend reasonably well with the existing doors.

I need someone to replace two internal door knobs — one bedroom door and one bathroom door. Both currently have the same style of round white door knobs. Please see the attached photos. I would prefer similar replacement knobs. Please provide a quote including the supply of two new door knobs, installation, and any additional fees. Thank you!

The door is currently not sitting correctly in the frame and it appears the following is needed; - Remove/adjust the existing cardboard/shim - Check and adjust the hinges as required; and - Properly realign the door so it sits correctly in the frame and opens/closes normally

Repair loose internal door hinge. Hinge screws have pulled out and holes are stripped. Need hinge holes repaired/reinforced and hinge securely refitted/aligned. Please bring appropriate timber dowel, screws and tools.

I have an internal painted door that previously had a hole in it. The hole was repaired using wood filler/wood dust, but the repair was not finished properly and the patched area is still visible. I’m looking for an experienced handyman/painter to professionally redo/finish the repair so that the surface is smooth, level and blends with the rest of the door as closely as possible, with no obvious patch marks. The existing repair may need to be sanded back, levelled/re-filled as required, primed and painted. I’m happy for the whole face of the door to be repainted if that will give a cleaner and more consistent finish, rather than just touching up the repaired area. Please include all materials, filler, primer and paint required in your offer. Photos attached showing the current condition. The main priority is the quality of the finish. I want the repaired area to be difficult to identify once completed. Please let me know whether you recommend repairing/refinishing the existing patch or another approach to achieve the best result.

I am looking for a chippy who can help me with 4 jobs. 1: Replace 5 internal door passage sets with new ones. The existing ones are all broken after 70 years so needs to be swapped out. 2: install a cavity slider privacy set to the bathroom cavity slider. There isn’t a lock on it now. 3: replace the front door dead lock as the key only goes in one way. There is an existing deadlock lock so I’m replacing like for like so hopefully reasonably straight forward swap out. There is also a bolt in the front door which needs adjusting. 4: plane the back door as it is catching on the bottom and adjust the door so it swings freely. It’s not bad but needs a plane on the door or the sill. Everything is being painted so can patch anything as needed. Looking for someone on either Friday 25th or Saturday 26th Sept. Thanks

Need to hang a standard internal door (all hinges and fittings are provided) Then need a gate ring latch to be installed on side gate.

I am looking for someone to install 5 new internal doors and handles for my house. These will be for 4 bedrooms + laundry I have already purchased handles but will reimburse for you to purchase the doors. I will remove existing doors. Thanks Andrew

Looking for someone to rehang an existing internal door so that it opens from the opposite side. I already have the door and all hardware. The job will involve removing and rehanging the door, repositioning the hinges and door handle/latch as required. Please bring your own tools.

A couple of older door knobs that have loosened over time and come out in your hand even after tightening

Hi there, The top hinge on one of my internal doors has come loose because the screws have stripped out of the frame. The door is currently sagging and won't latch properly. To save us both some questions, here are a few quick details: Door Type: Standard internal hollow/solid core wooden door with a standard metal hinge. The Issue: The screw holes in the jamb are maybe stripped or come out, so it likely needs longer screws, wood plugs/dowels, or wood filler so the screws can bite again. I'm not 100% on issue but video below. Tools/Materials: I don't have the specific longer screws or wood filler on hand, so you'll need to bring your own standard toolkit and fixings. I'm not handy. Access: Easy parking available right out front, with permit, ground level. Please let me know your availability to pop by and knock this out. Thanks!

I need a reliable handyman or locksmith to replace 4 existing internal door handles with new ones. Details: The Hardware: I have already purchased and supplied the new hardware (Lockwood 31-55mm Satin Chrome Entrance Levers). They are brand new and on-site ready to go. The Scope: The doors already have standard handle cutouts which should closely align with the new Lockwood levers. However, I need you to check the fitment first. If they don't line up perfectly, you will need to slightly widen or adjust the existing timber holes/latches so the new hardware sits flush and operates smoothly. Tools needed: Please bring your standard tools, along with a chisel, files, or a drill/hole saw kit just in case minor timber adjustments or latch recess tweaks are required. Timing: Looking to get this done ASAP.

Three internal doors and two wardrobe doors replaced. Supplied and fitted

Fit and cut out internal door handle, has to be a very neat job, if you cannot do it correctly please don’t apply for the work.

We have two internal doors that struggle to close so they need to be sanded. 1. Unhinge two doors 2. Sand bottom of doors 3. Rehinge doors Both internal doors need to shut properly.