Find a local network troubleshooter in VIC

Add 3 x TP-Link RE815XE extenders to TP-Link VX420-G2h modem/router for EasyMesh network. Check that 2 TV, several Google Home devices, and Tapo doorbell/camera are all connected to Mesh network.

We have a shop at Eastland Shopping Centre. We are getting a drop out of internet at one point- Telstra needs to check if that port cable from back office to counter is not damaged. Their comment is as below: “We need cabling checked from ntu to the cisco router, coving ntu to patch point > internal patch point to patch point > patch point to cisco router. We believe the fault to be between the internal patch points. Collecting photos of these connections could also be helpful.” They want electricians to check and confirm if that is not damaged We also have multiple port going on if one is damaged Shop open 9:00 to 5:00 everyday

Set Up Wi-Fi Access Points Throughout 4-Storey House We have just moved into a 4-storey house and currently have the NBN/Wi-Fi router on the first floor. The Wi-Fi signal doesn’t reach the upper floors properly. The house appears to be smart-wired, with Ethernet/network ports throughout the house and in multiple rooms. I’m looking for someone experienced with home networking/Wi-Fi access points to: * Check how the existing Ethernet/network cabling is connected * Identify where the cables terminate * Connect/configure the existing network ports * Set up Wi-Fi access points or mesh nodes on the upper floors * Configure everything so we have reliable Wi-Fi coverage throughout the house * Advise on any additional equipment needed (switch, access points, etc.) We use Telstra NBN. Ideally looking for someone with experience in networking, Ethernet cabling and Wi-Fi access point installation, rather than just general IT support. Happy to send photos of the existing ports/equipment before the job.

New internet provider need wifi set up

Require a home network / computer security review to ensure it is safe from hacking, including router settings, etc.

2 Cable Runs one approx 30 m and the other approx 25 m Both from ground floor cabinet to roof cavity and across to 2 different locations and down thru timber cavity walls , one of the locations has an existing network plate

I had installed an erro max 7 replacing a google pro system the install needs to be tidy up and made to function properly , you must have skills in the eroo and google network systems and the associated apps if not don’t reply as I have already had a techie come to no avail

Need 2 data cables run from garage NBN area to new ceiling Access Points, one in lounge, one in front office. One less than 10m, the other just under 20m. Prefer solid core / quality CAT6(a). Also need power point fitted to back wall of garage (backs onto Kitchen, where existing points are). House is single storey, concrete tile.

Hi, I’d like to get a quote to move my router from the front of the house to a more central location, approximately 15m away. The NBN box is currently near the front door. There is an existing old cable route under the floor, so ideally the new Ethernet/data cable can follow the same route. Please let me know the approximate cost. Thanks!

We’ve just moved into a new office in Cremorne and need a electrician/data cabler to attend tomorrow (Friday 4 September) to get our network and Wi-Fi setup completed. The IT will be onsite at to guide whats required. We already have internet connected at the premises and our IT team will assist with any network configuration required. Location: Cremorne VIC 3121 Timing: Must be available tomorrow, Friday 4 September at 9:30am

Need someone who understands unifi home network. Previous owners left cameras, smart doorbell, wifi spots, and a unifi cloud key gen 2+ (and all cabling). I just need to know what (if anything) else to buy, and for it to all be set up. I have a router provided by my isp and a couple of cheap tp link switches if they are of any use.

We are upgrading to NBN FTTP and require the following work to be completed: Install a power GPO next to the NBN fibre box to provide power to the fibre box. Run a network cable from the NBN fibre box to the modem at the back of the store approximately 20 metres away. The cable should be properly routed through a cable duct or concealed where possible. You may use a nearby existing data point to extend the network connection to the back of the store. Please refer to the photos for the existing data point locations.

Looking for an experienced small-business network technician to upgrade and troubleshoot our network at an optometry practice in Heidelberg. Installation must be completed after 5:00pm on a weekday to minimise disruption to the business. Current setup: • NBN FTTP • NetComm NL1901ACV router with intermittent dropouts • Existing network switch and Ethernet cabling throughout premises • Multiple wired PCs and local server • VoIP phones • Wi-Fi Considering a TP-Link Omada ER7212PC with an Omada Wi-Fi access point, but happy to take advice on the most appropriate equipment. Work required: • Inspect existing network, switch and cabling • Install and configure replacement router • Install/configure Wi-Fi access point using existing Ethernet cabling • Configure DHCP/static IPs as required • Ensure server, PCs and VoIP phones continue operating • Test internet/network stability after installation • Troubleshoot the existing dropout issue and confirm whether the router is the likely cause Ideally looking for someone experienced with TP-Link Omada/UniFi, small-business networking, VoIP and Windows server environments. Equipment can be purchased beforehand based on your recommendation. Budget is for labour only; networking equipment will be supplied/purchased separately. Please include your relevant experience, availability and estimated labour cost.

Configure UniFi access point to network, configure Dahua intercom to connect to 2.4ghz

My Partner is home with my adult kids and she is having trouble with the DSCO internet set up I put in. I am away for work. She said that it is not connecting to certain sites that she needs for work and son can't connect to uni. It is fiber to the house and I did a scan with superloop (Provider) And it looks good. I have the DESC all and ever since yesturday I can't see the network anymore. Might need to re-do the whole thing. System is all Deso M5 units,

I have been dealing with what could best be characterised as an APT. I need some to help me diagnose issues with my home network, and get at least one of my devices into a known good state. I have several iphones and google pixels in particular that I do not want to dispose of. If it turns out they are enrollerd in a malicious MDM then i need help choosing a path forward and determining where things are at, One way or the other.

I need network and cable management for a new build. All the wiring is done. Need all the cables tested. Camera plugged in and maybe an access point.

I’m looking for a registered data cabler to install wired Ethernet backhaul for my home mesh Wi-Fi system. The NBN modem and main mesh router are located in the lounge. I need two separate Cat6 Ethernet cable runs installed from the main router location: ~ One cable run to a mesh Wi-Fi point near the front door ~ Two connections to the study - one for the mesh Wi-Fi point and one for a desktop PC The job should include: ~ Three Cat6 Ethernet cable runs ~ Three Cat6 Ethernet outlets at the lounge/main-router location ~ One Cat6 Ethernet outlet near the front door ~ Two Cat6 Ethernet outlets in the study ~ Cat6-rated wall plates, outlets and terminations ~ Testing of all three cable runs after installation ~ Confirmation that the two mesh points are connected using wired Ethernet backhaul Please include all cabling, wall plates, connectors, labour and testing in your quote. I estimate it's probably 20 to 30-meter cable runs from the lounge/main-router location. Only registered or appropriately qualified data cablers, please. Location: Greenvale House type: Single-storey (medium-sized home) Roof access: Available

We have NBN network, with a google nest mesh system. We have issues getting the printer connected, and want to be able to print, scan, etc from desktop computers to desktop computers. Brother MFC unit.

Existing network need help to reset and set up on new computer and add one outdoor device. At the moment we have 3 access points Templestowe location