Find experienced local tradies in Inner South West Sydney

I have a 117 square basement concrete slab just need to gyprock the whole roof roof needs to be 300mm of roof needs to be set as well ready for paint needs to be completed bye next weekend Need the whole job done metal framing , gyprock , setting and sanding ready for paint

Hi, I need a licensed electrician to install two new single power points (GPOs) next to the toilets in two separate bathrooms for smart bidet seats. Property type: House Wall type: Tiled wall (over Gyprock) – please see attached photos

I have approximately 3 square metres of kitchen ceiling damaged by air conditioner condensate water leak. The existing plasterboard needs full replacement. Work scope includes: 1. Remove all damaged existing ceiling plasterboard 2. Clean and remove mouldy old insulation 3. Inspect all timber battens and ceiling framing 4. REQUIRED: Install brand new Gyprock MR Moisture Resistant Blue BOARD ONLY (NO standard white plasterboard) 5. Complete full plastering, joint taping, angle bead, skim coat and full sanding 6. Install two Access panel, cut holes for down light fitting as original shown in photo. 7. Make ceiling fully smooth and ready for painting 8. All construction rubbish to be fully removed from site Important notes: • NO PAINTING REQUIRED • NO AIRCON REPAIR REQUIRED • Please provide fixed price quote. No hidden fee pls. • If timber battens are rotten after opening up, please advise extra cost separately before proceeding. • Licensed plasterer with ABN and insurance preferred. Location: Oatley NSW 2223 Site access available.

Assembly and Install this awning and silicone around awning. Above a roughly 2.7m door. Ground floor We have a ladder This is the product https://www.tiptopyards.com.au/product/awnings/bremen-door-awning-awning-kit/

I had a crack roof tile that’s now fixed but have a wet patch in my ceiling that needs patching. The gyprock patch that’s needed is roughly 30x30cm.

I need a joinery that assembly built in wardirobes. You need drill, ladder and expert in built the wardrobe. There is 2 wardrobes

As described Bathroom render before waterproofing and tiling

We are renovating a bathroom for an old apartment in a block. Its on L2. No lift. We need a renderer who can fix all the render and make it level ready for waterproofing and tiling. We are doing all the strip out. Dimensions: 1.7 x 2.3m x 2.4m height. Dont worry about my budget. I am not sure of the cost. I want someone who is clean and capable to do the job neatly. Also we are a renovation builder, so more work to come for the right person. Happy bidding !

Need to sheet 2 small ceiling areas (3 sheets) then set and patch throughout. Looking for 1 guy for a day, preferably with setting experience.

Gyprock repair, two holes roughly 100x100 and 150 x 250. Just need the holes patches and sanded. Need the job done today

I want these two spaces covered with Gyprock I will paint flash as possible

Job consist of hanging a large size canvas in a staircase. 1. drilling and installing of plasterboard anchor & screws (supplied) in one aligned row. (See photo) 2. Requires a ladder to reach at least 4 metres height reach with leveller or the likes for a staircase. (See photo of staircase) 3. Art Piece only weights 4kg and measures 204x196cm. (See photo)

Repair gyprock and paint it same colour as the rest of the wall

Fix gyprock wall. Paint provided

Gyprocking, set and sanding ready for paint 3 walls 2.4mx3.2m both sides. All materials supplied.

Fix ceiling gyprock it has fallen i will provide the gyprock

Gyprock to see if possible to do

The RCD labelled “Protected Power” (C20, 30mA) trips the instant I switch it on, so all power points are dead. Lighting circuit is fine. Cause is known: insecticide spray went into one power point and the tripping started immediately after. The RCD has been off since and I haven’t touched the outlet. What I need: the affected outlet inspected and replaced, and the circuit tested.

Looking for a Gyprocker to rectify cut out as per picture can be made into door or just sealed and patched and sanded as well pergola ceiling has been patched but needs Sanding ready for painting and any other minor patching on ceiling as per pic

Mount folding table to drywall I need someone to securely attach a folding table/unit to a drywall wall. The table is already assembled and has a base that sits on the floor, so the wall screws will not be carrying the weight of the table. They are mainly there to secure the top of the unit to the wall and prevent it from tipping forward. There are 4 pre-drilled screw holes along the top rear section of the table. The main complication is the skirting board at the bottom of the wall. Because of the skirting, the back of the table cannot sit flush against the drywall. I have therefore bought two boards/spacers the same thickness as the skirting board to sit behind the table and fill the gap. The job would involve: - Positioning the two spacer boards behind the table - Drilling through the existing 4 mounting holes, through the spacer board and into the drywall - Using suitable drywall anchors/fixings to securely hold the unit against the wall - Making sure everything is straight, secure and neatly installed Please see the attached photos, which should make the setup much clearer. Please bring the appropriate screws, drywall anchors/fixings and tools required for the job.