Find experienced local roofers in WA

Need to repair the external guttter for my property

Hi, Handyman needed. 4 roof tiles got dislocated, so needs to rearrange them. It’s a very small job.

-Need new wire on a clothesline (wire will be provided) - need evaporative AC drain pipe to be modified to drain into downpipe

Need someone to clean the gutters around the house

There are gaps in sections of the roof flashing that need to be sealed or refitted to prevent water leaks.

Approximately 50 50 msq laser lite polycarbonate installed

Need an experienced roofer to rebedding and repoint roof tiles on a tiled roof. • Approx. 6–8 tiles • Issue is bedding/pointing (not full roof) • Single-storey house • Please include materials & labour in your offer Photos available on request. Inspection welcome.

A roof tile(s) has either slipped or broken, that needs replaced. I have spare tiles

Following a renovation, where insulation was removed, I need new insulation installed. Will require entry to the roof space from above (tiled roof). The area is roughly 50sqm (I cannot be precise as the ceiling is in now place). Photos are taken during the renovation! Also wanting existing installation put back in place where pulled up by electrician. I will provide the insulation.

Tesla model Y roof rack installation needed

Hi, I need a single roof flume installed on a colorbond roof (25 degree pitch) to connect an exhaust fan from our ensuite. You will need to provide the flume, flashing and silicone. The fan already has flexi duct attached, just needs to run to the flume

Gutters of 3x2 single story home to be cleaned.

Hello - I've purchased a couple of solar whirlybirds for my new colorbond roof, but I don't have any nibblers/etc to cut the holes out to suit. I'll need 2x approx 25cm holes cut at locations close to the roof ridge (locations are already marked). It's a single storey house with easy roof access. There's sarking (thin insulation) below the roof sheeting - not sure if that affects how easy this task would be. Note - this is not an installation project! I'm going to try and install them myself. This is just cutting the holes.

I need a muller type pvc air vent supplied and installed to my aluminium ute canopy roof for ventilation. They can be purchased from several suppliers in Perth including dunn and watson, bull motor bodies etc. Requires holesaw/pop rivets & sealer for installation.

Looking for a skilled handyman or roofer to repair or replace a damaged transparent roof panel in my outdoor pergola/patio area. One clear corrugated panel is cracked/aging and needs to be securely fixed or replaced to prevent leaks and improve weather protection. Timber beams are already in place. Task includes: • Inspecting the existing transparent panel • Supplying and installing a replacement clear panel (polycarbonate or similar) or re-fixing if reusable • Ensuring it’s watertight and safely secured • Cleaning up after the job Details: • Access is straightforward • Prefer someone with experience in pergola/patio roofing • Please bring your own tools • Tasker will purchase panel on our behalf When: Flexible – ideally within the next 1–2 weeks Budget: Open to reasonable offers (please quote) Notes: Happy to share photos (see attached) and answer any questions before accepting the task.

Installing a kings rooftop tent onto a car

We have our own paint and 3m high ladder provide (recommend if you have your own and higher). I need someone to do the painting 2-3 m long, 10cm width gutter. The grey area in the photo circled. Should take less than 30 mins

Roof is currently experiencing water ingress during windy rain due to deteriorated gable ends and barge boards. This task is to complete a professional inspection and provide a quote which will ensure the scope prevents any future leaks in the roof. What I had as previous scope details for reference only if helpful: - Close in two gable ends (east and west) using weather-proof cladding. - Install new flashing at the gable-to-tile junctions, installed under lifted tiles with correct lap (no surface-mounting). - Seal all new cladding joints, edges, fixings and penetrations with exterior-grade polyurethane. - Paint the gable face/barge/fascia after the work – plain white colour. - Re-seal and paint barge boards/fascias. - Chimney: clean and reseal flashing/penetrations, including lifting tiles to inspect the under-tile soakers/back-tray; quote separately if re-flash is required. - Install 2 whirly-birds on the tiled roof to provide ventilation, including proper flashing and seal around base. Property is rented so I'll help to coordinate with property manager for access (internal & roof). Conditions I'll need please: - You have your own public liability insurance. - I need a tax invoice on completion. - Work must cause no damage to existing roof tiles. - Before and after photos required please. I am open to other ideas or methods to achieve the same result - refer to attached photos.

Remove and dispose of an old kerosene heater tank and a solar water heater panel. Kerosene heater is bolted to a wall and has mostly been drained. Solar water heater is located on the roof.

Needing roof tiles replaced Looking to get quotes Photo just showing where solar will be in future. No solar currently I have the new tiles which are the same size as old ones Tiles are easy - only ones that need to be cut are in half as it is a straight roof My partner will be able to assist if required Price negotiable