Find a local network troubleshooter in VIC

I am looking for a data point installer for 4 data points and install network rack

I need a technician to help with network cabling at our office in 150, high street, preston Run a Cat6 ethernet cable from the 1st floor (where our ISP modem is) down to the ground floor (where our network equipment is located). There is already an existing ethernet cable running between these floors that you can use as a guide for the route. Organize and label the existing cables at both the router and switch locations. Nothing major — just tidying up the cable runs so everything is neat

I need an electrician or data cabler to install 3x ethernet ports in a single-story house built on concrete slab and Tile roof. See attached image The NBN router is located in the living room. I'll need: (1 x port) in Living to pass through to Lounge Room (1 x port) and (1 x port) in study (direct connection to router in living) See image. PINK spots for the new ethernet ports. Please provide a quote for all materials and labor, including running the cables and installing the wall plates. thanks

Small Bakery Business looking to re-Network office space. Need experience in re-linking phone line, internet, internal phones, alarm system etc. All in a bit of a mess and needs a good sort. Everything working well just a good spring clean and sort. Need to schedule a meeting onsite first to draft a plan then to do works on a Friday morning.

There are three network cables connected to fixed wall outlets.

I want the two network cables to be pulled from main router to my garrage, concealed nicely, no termination needed but only the cable pulling

Need to run a network cable from upstairs to downstairs via basement area.

Hi there, We’re looking for a highly experienced home networking and smart home technician to assist with troubleshooting and improving the network setup We recently upgraded to Aussie Broadband Fibre NBN (500/500) and initially the service performed extremely well for first months. However, we are now experiencing reliability and performance issues that appear to be related to our internal network configuration Current Setup • Aussie Broadband Fibre NBN • Google Nest Pro mesh Wi-Fi system (5 access points) • Existing in-wall Ethernet cabling throughout the home Scope of Work Diagnose & Optimise Network We need an experienced networking professional to: • Troubleshoot and optimise the current Google Nest Pro mesh setup • Ensure stable, reliable Wi-Fi coverage throughout the property (at 500MPBS)_ • Review overall network configuration and performance • Identify any issues with topology, interference, switching, backhaul, or device placement We would like to hardwire the Google Nest Pro units using the existing Ethernet cabling already installed throughout the home. As we’ve recently purchased the property, we do not currently have a wiring map, so part of the job will involve identifying and testing where the Ethernet ports terminate. New Ethernet Cable Run We also require a new Ethernet cable run from the current NBN modem/router location to a communications cupboard in the hallway. Details: •run x1cable 15 metres total • Easy under-house access available • Good access between hallway comms cupboard and living room • professional cabling work required We’re specifically looking for someone with strong experience in: • Residential networking • Google Nest Pro / mesh Wi-Fi systems • Ethernet diagnostics and cable tracing Pricing • $170 call-out fee ( first hour of labour ) included only in this listing • + seperate $90/hour thereafter (extra so, not included in this listing) Possibly 3–6 hours total, depending on troubleshooting and cabling requirements.

Need to connect 2 of TP link AC 1750 extenders, will all have to become 1 network. Telstra router/modem sitting in garage Rear studio, approx 45 meters away. Double story home

I have Telstra NBN fiber optic to home and need good wifi signals around home. Also have a rear studio detached. The NBN is running there also, I can’t be relying on a wifi signal there so need maybe another modem there?….

Hi, I need help finishing a home network setup at my house. The house is already wired with Cat6 LAN points. I have a rumpus/living area panel with 5 LAN ports, and I’ve identified that 4 of them connect to rooms in the house. There is also an NBN-labelled port, a garage LAN port, and a loose Cat6 cable near the old NBN/garage area that need to be identified and tested. Looking for someone experienced with data cabling/home networking to: * Identify and test the mystery Cat6 cable/garage/NBN link * Terminate loose Cat6 cable(s), likely T568A * Confirm which port goes where * Connect the incoming line to the rumpus distribution panel NBN FTTP is already active and working. I just need the internal LAN cabling finished properly so the room ports can be used. Should be a straightforward job for someone with the right tools/tester.

All home devices needs to be connected with WiFi. Camera google home etc

Complete home network setup with to link Omada oc200 controller, er706w router and es220gmp poe switch for two side by side dwelling. One house has internet second one waiting. All cat 6 cables are all patched already in the building.

Parts of home network down - Ethernet ports need identifying - possible unify issues - reset factory and reset some system

Install network connection from garage to hallway

I’ve recently upgraded my home network equipment and need an experienced IT/network technician to configure everything properly. The system was previously working fine on an old modem/router installed by electricians. I have now replaced this with a new router (TP-Link Omada ER605) and added a 16-port switch, but I cannot get everything working correctly. Current setup includes: Bosch 3000 alarm system 6 x Dorani security cameras 2 x long-range WiFi access points ~10+ Ethernet data points throughout the house NBN connection (1000 Mbps) Issues: Cameras/apps no longer accessible remotely Router not configured correctly (likely DHCP / IP / port forwarding issues) Network worked previously, so this is a reconfiguration rather than new install What I need done: Proper setup/configuration of new router (WAN, DHCP, etc.) Configure static IPs for cameras and alarm Restore remote access to camera system Connect and configure 16-port switch Tidy and organise cabling Cabinet / rack: I have not yet purchased a wall cabinet I would like advice on the best cabinet/rack for this setup Ideally you can recommend (or supply) a suitable option Cabinet installation can be done same visit (if available) or as a follow-up Requirements: Must have experience with home/business networks (not just basic cabling) Familiar with routers, switches, IP addressing, port forwarding Experience with CCTV/security systems preferred Please outline your experience with similar jobs when applying.

internet issues with my WIFI extender

WIFI Extender not connecting to my network

replacement modem network reconfiguration

Check the existing network switch and the corresponding ports and connect the switch to NBN to setup VoIP calling