Find a professional mdf contractor near you

Looking at an experienced handyman to supply and install MDF skirting boards around tiled areas in my newly constructed home Skirting to be fitted neatly against existing floor tiles (no gaps). All corners and joins to be properly cut, aligned, and finished. Existing walls are painted and ready for installation. Tiled areas to be included: entrance and passage, living room, kitchen, theatre room and scullery. Also some area outside the bedroom Profile Preference: Splay 1 Skirting Boards Size of 92mm, painting to be adviced I believe the total measurement is about 67 LM, however happy for you to visit the site and take measurements.

Hi there! Some cutting in the kitchen is needed to accommodate new appliances. 1. Existing marble bench stove cutout needs to be expanded by about 1cm on one side to fit the new stove. 2. Some wooden boards need to be removed or cut so that dishwasher can slide into the gap. NOTE - if you are able to disconnect a gas stove or connect dishwasher to water this would be a bonus so please mention it! Thanks a bunch, Dan

I will be purchasing 5 sheets of mdf from bunnings that I need to cut into 10cm strips for wainscoting in bedrooms. Can you please quote for cutting the sheets

We have one large piece of ribbed MDF board which needs to be cut into three pieces. You will require a circular saw and two trestles for the job. Job to be completed at our address in Mernda. A very quick and straightforward job. It is a 2705 (H) x 1200 (W) tongue and groove board . It needs to be cut into 3 870 (H) pieces. 1st piece: 870 x 1100 2nd and 3rd piece: joined together to make a 870 x 2250 length.

I have a 9mm MDF board that I require to be cut in 76.2 cms round shape. If you are able to do this, please provide me with a quote

9mm MDF panel: I'm after someone who can cut out small rectangles (40x60mm).

I will supply MDF panel. Just after someone who can cut out small rectangles (100x150 and 150x200mm). - Due date: Flexible

Refer to image. I need to cut 8 rectangular pieces the exact size as the smaller piece shown. Already have the MDF. That’s it.

Cut 2 x MDF planks into 12cm strips. Total strips 14. Material available.

Hi all, This one has been on our minds for a bit - hoping for a professional to do the following; - Purchase MDF Panels - Paint MDF Panels - Cut to size if required - Cut out PowerPoints within MDF - Install MDF Panels on feature wall. - Install MDF panels under island bench. - Mount TV on Feature Wall once MDF installed (75inch) Areas are pictured within this task, for reference. Paint: to match the’Matchamisu’ range, like below. https://www.bunnings.com.au/kaboodle-900mm-matchamisu-heritage-medium-rangehood-doors-2-pack_p0437311 MDF panels for feature wall; 4m W x 2.7m H https://www.bunnings.com.au/easycraft-2700-x-1200-x-9mm-easyvj100-primed-general-purpose-wall-lining-mr-mdf-e0_p0440018 MDF panels for under island bench: 3m W x 85cm H https://www.bunnings.com.au/easycraft-900-x-1200-x-9mm-easyvj100-wall-lining-primed-general-purpose-mr-mdf-e0_p0330843 I will provide the following for you: - All panels (you let me know how many of each are required). - Paint - TV & Tv mount supplied onsite. The tools, glues and nails (glue nails etc), to be supplied by installer.

I need a 3mm thick 2400x1220mm piece of MDF cut into 2400x100mm thick strips using a table saw or similar. The cuts need to be very straight! I can drop off the MDF and pick up if local to Noble Park/Springvale.

Hi all, Please see: https://www.bunnings.com.au/easycraft-2700-x-1200-x-9mm-easyvj100-primed-general-purpose-wall-lining-mr-mdf-e0_p0440018 Looking for someone to install this on my lounge room wall. This process will require: - remove the TV from the current wall mount (75inch tv so it is not light). - install MDF. - cut outs as necessary (allowing for PowerPoints etc). - re-install Tv and wall mount to new desired height. Installer to supply tools needed for the job eg. Glue, liquid nails etc. the installation guide can be found on the webpage above.

I need someone to install a lightweight MDF board as a shelf inside a built-in mirrored wardrobe (see attached photo for reference). The MDF board is already purchased (Bunnings ) Job Requirements: • Cut the MDF to fit inside the mirrored sliding-door cupboard. • Securely install it as a shelf (3 ft height). • Supply any brackets/fixings required for support (e.g.shelving clips). • Ensure neat and stable installation with no visible damage to the existing cupboard frame or mirror. 2 MDFs on both sides of the cupboard.

We require 3x easycraft 2400 x 1200 x 9mm panels cut to size and fixed to 2 bar frames. See images attached of 1 of the bars. Each bar will have a front panel and 2 sides. Panels to be fastened to 19mm steel tube frame

Task 1: MDF door is already cut and fit to size, the existing hinges broke so need new ones supplied and the door reinstated Task 2: install a new door knob as the existing one has broken off the door. Supply new door knob and install

Cut 60mm strips out of 3mm MDF

To supply & install mdf slatwall for music room,to hang guitars,slatwall to be installed on brickwall

Supply and install kitchen panel approximately 82cm x 52cm

Need a handyman or carpenter to cut and screw MDF sheets over a glass door for security x 2. Glass door is approximately 1900 x 2000mm MDF sheets provided. Need to be cut to size and installed horizontally. MDF sheets are 3600 x 800mm

Description: I need someone with the right tools and experience to accurately cut and mount a new MDF fascia panel for an underbench oven. The panel is white melamine MDF, 16mm thick. You'll also cut a centered oven opening in the panel and help install it using provided battens and shelf (already cut and in place). What I have: Full 16mm white melamine MDF sheet Shelf & battens already installed Measurements & cutout dimensions are marked Screws & pilot holes ready Old fascia as a reference (optional) What I need from you: Precision cut fascia panel to 697mm W × 1115mm H Cut centered oven opening: 568mm W × 596mm H, starting 150mm from the top Neat jigsaw work, no chipping Securely screw fascia into cabinet battens (holes marked) Bring your own tools (jigsaw, clamps, pilot bit, etc.) Downstairs of house and heaps of room to work