Find a professional internal door contractor in VIC

External sliding door needs repair (possible new track & wheels) & internal door needs adjusting (does not close)

I have an internal door that is slightly too high. I need a few cm's cut off the top and help to hang it again.

Two internal doors - normal, timber swinging doors for bedrooms - dont close properly. One hits the top frame like it’s too high, the other doesn’t click close. Might be alignment issues.

I require a qualified carpenter to swap over 4 old internal doors with new ones. Doors and door hardware have already been purchased. Doors are 2040 x 820 x 35. Please only qualified carpenters should provide offers.

To replace 1 internal door to fit current hinges, handle, lock and latch. Current door measurement: Depth 35mm, Width 816mm, Height 2033mm. Door not provided. Painting is needed. Latch backset size 60mm, latch case size 70mm. Lock bore hole aprox. 55mm. Latch lock hinges provided. To be done ASAP.

We have an internal door frame with hinges, and we bought a new door that needs the handle installed and hung onto hinges

Supply and instal a 2040x815 door unpainted, with all hardware included

Need 2 white internal doors supplied and installed in Tarneit – 1 sliding and 1 standard hinged. Sliding door approx. 1860mm (W) x 2130mm (H) Bathroom door approx. 820mm (W) x 2130mm (H) Both doors to include frames. Photos attached.

Internal door is not opening (one-way) in the hallway of ouor home-so when the door is closed, you can not get back into the lounge area. You will need tools and know-how to take the door hardware off the door, and either repair or replace the hardware. Please do not respond if you do not know how to fix this issue.

I have a compartment in my unit where my fridge is located - as you can see the door has completely come off, including three of the four hinges (the backing for the top one is still attached to the board). The three hinges are still attached to the door - I'm looking for someone who can get the door reattached to the panel. Happy to cover the cost of new hinges if needed.

Install 13 internal door handles. Replace old white one in photo with new handle in photo.

Need about 3cm taken off the bottom of a door

Three internal doors need sanding back after carpet install and reattached to door frame

Arghhh - I need some help TODAY (Wednesday if possible) If you're free and around the Hallam area and are a chippy/handyman... we have just recently had carpet laid in 3 x Bedrooms. The carpet layers took the doors off - likely because the carper is a bit thick and the doors need a tiny amount shaved off and rehung... and I need this done ASAP. The job would be head to HALLAM - gauge how much needs to be trimmed... take door out the front to cut (don't cut inside please) and then rehang the door... The doors are already off, the screws are there... it is very EASY work I just don't have the time to do it today,... but ideally needs to be done TODAY. If this can be squeezed in - let me know! Cheers

I need 2 doors fitted. I have the doors here just need them installed on a bedroom and bathroom.

Need someone to cut 2 internal doors (35mm) following a pattern, to install cat doors.

Hello, I’m needing someone to fix my bedroom door in my house. 1 x bedroom door not square, looks like top hinge has dropped

Looking for someone to repair a hole in a standard internal hollow-core door. One side has a medium-sized hole (approx. 15cm), and the other side has visible cracks from the same impact. I’d like the door patched and repainted to match as closely as possible. Photo of both sides attached for reference. Ideally looking for someone who can do a neat job this week. Location: Southbank Flexible with timing. Thanks!

Need to replace internal door. Replacement door has already been purchased so you just need to transfer handle and hinges to new door and then hang into position.

We have 6 internal door handles that need to be replaced with new ones. 4 x passage sets and 2 x privacy sets. The hole for the latch will need to be cut larger as the existing holes are too small for the new latch.