Find a reliable appliance technician in Southbank

Change the rubber door seal for washing machine

Hi, the freezer is working perfectly and freezing as normal, but the fridge compartment is not cooling properly and there doesn’t seem to be any cold air coming through. I’d like to arrange for someone to inspect the fridge and diagnose the issue, please.

Can't connect the watching machine. The sink keeps leaking.

Our dryer turns on and runs, but it is not producing any heat, so the clothes are not drying. We need someone experienced with dryer repairs to inspect it, diagnose the issue, and provide a quote for repair. Please mention your call-out or inspection fee in your offer.

I need a qualified appliance technician to service and deep clean two Miele appliances in my apartment. The warranty has expired, and I am experiencing specific issues that require more than a surface wipe down. Appliances:::: Miele Washing Machine (Model WCA 020): Needs a full service, drain pump check, and internal drum clean. Miele Condenser Dryer (Model TCB 140 WP): CRITICAL ISSUE: Lint is escaping into the room during drying cycles, and dust is not being expelled. I suspect the internal condenser unit is clogged or the filter housing seal is compromised. Scope of Work Required:::: Dryer:::: Remove the bottom kickplate and extract the condenser unit. Deep clean the condenser fins (remove packed lint/dust) using a brush or low pressure water. Vacuum the internal fan housing and ducting behind the condenser. Inspect the rubber seal around the lint filter housing for tears or warping. Reassemble and run a test cycle to ensure no lint escapes. Washer:::: Clean the drain pump filter. Run a drum cleaning cycle (I can provide detergent or you can use yours). Check door seal for mold/debris. General:::: Wipe down exterior and check water hoses for leaks. Requirements:::: Must have experience specifically with Miele condenser dryers. Must have tools to safely remove and clean the internal condenser unit. Please provide your own vacuum with a long hose and brush attachments. If any parts (like a filter seal) need replacing, please quote me before purchasing. Location: [Focus Apartment Southbank] "IMPORTANT::: My budget Range: $150 – $350. Please provide a diagnosis and quote before starting any work. If the issue is just a clean, please quote a fixed price (Target: $150-$200). If parts are needed (e.g., seal, pump), please quote the parts cost + labor separately and get my approval before purchasing. If you find a major mechanical failure (motor/PCB) costing over $400, please stop and let me decide whether to repair or replace."

Looking to have an integrated dishwasher installed. Cavity prepped and ready. The cabinetry/panel will be put on after the fact. Send offers through Keen to get it done ASAP.

Need help in getting my washing machine connected to my new place …

The cabinet currently has two drawers in it. I need the drawers and runners removed, the internal shelf or divider taken out, and the opening cleared back to a clean cavity the dishwasher can slide into. Then I need a single custom door panel made and fitted to the dishwasher door, matching the existing white cabinetry as closely as possible. There’s an existing power point on the back wall of the cavity that stays where it is, so just work around it. Cavity is roughly 720mm deep. Dishwasher is a Fisher and Paykel 60cm integrated, 597 wide by 554 deep, so I’ll have exact panel specs from the installation guide for you.

washing machine error code e37

I have a 5-burner Smeg gas cooktop (middle burner is oval-shaped) with a continuous sparking problem. The issue started after cleaning about 2 years ago. Since then, when the power is turned on, all burners keep sparking continuously without stopping. To manage this, I’ve been turning off the power at the switch and using a lighter to ignite the burners. Gas is working fine and all burners function normally when lit manually. The issue seems to be related to the ignition system, likely a faulty ignition switch or spark module.

I believe it is a Fisher & Paykel DishDrawer possibly DD60 series. Currently getting cleaners to inspect and try to diagnose the issue, but from previous guest they said the dishwasher would continuously beep and the cycle wouldn’t start, with water pooling at the bottom. Tray and parts have been taken out to clean from any blockages

Dishwasher and in built microwave are not working properly (microwave does not heat and dishwasher beeps and stops 5min from start of cycle)

The task involves removing an older 60cm Smeg Rangehood (SA480T) and installing a new 60cm Smeg Rangehood (STH600X1). I need to avoid modifications to external cabinetry. Internal adjustment, that is not visible, is okay. I have shown the specification for each rangehood in the pictures. Both rangehoods have the same dimensions, however I am not sure if there will be any issues with the existing duct diameter and duct hole position. See the attached pictures / photos which has dimensions / specifications. Location is an apartment building on St Kilda Road, Melbourne 3004.

Need to fix the door for an integrated dishwasher Haefle It is a new compact dishwasher that was installed already last week. Need a person to fix the new door panel( already available with instructions) It is not dishwasher door - it is the door that is encasing the dishwasher door which pulls down - as part of cabinet as it is integrated. All instructions are available. Parking on street and paid parking only. Need to fix the door the same day as you come in and complete the work.

Oven was working but not turning on in an apartment, need someone to come and investigate. Model: Omega OBO654TGG

I need to repair the cooktop — one burner knob cannot be turned on because it is stuck, and another burner will not light up

Temperature stuck at -8°C: The set point is -22°C, but it won't drop further. ​Ice blockage suspected: The compressor light (snowflake icon) is solid ON, but I can barely feel any airflow from the evaporator grilles inside.

Need some friendly face to help us fix a washing machine, it runs some cycles but won’t carry through with washing. It loads some water in to the drum and then stops. Tried a couple hacks but no luck.