Find a reliable appliance technician in St Kilda West

When I got my hot water system changed, the plumber that changed it took the dishwasher tap away. Need a tap to be put in for the dishwasher. The other plumber won’t respond and I do not ever anyone recommend using him.

Model of the Washing Machine is: Samsung WD85T504DBE (8.5kg-6kg Combo Washer Dryer) We found coin got stuck in the machine and physically sliced through the plastic housing near the drain pump/outer tub (please see the attached photo). It caused a significant leak during our last washing; now all the water has been cleared. I am looking for a technician to identify the exact broken plastic component, source a new replacement part, and install it properly. I am ONLY looking for a proper part replacement and no silicone, glue patching, or temporary fixes. I want the machine restored to a reliable, long-term working condition. We need the washing machine to be done as soon as possible. Since I am travelling overseas on May 23rd. I need someone who can ideally come in to inspect, quote the exact part, and ideally complete the repair before I leave. When making an offer, please state: 1. Your call-out/inspection fee. 2. Your estimated labour cost for this type of replacement. 3. Whether you have access to Samsung spare parts quickly.

Dishwasher is not draining properly. Also want a small pump to be hooked up to my water feature. I have the pump.

Need to disconnect gas oven

I have a small Omega dishwasher in great condition, with no physical or electronic damage. Unfortunately it’s not draining, though, and I don’t have the tools or knowledge to fix. Hoping someone can swing by and help. Should be a very quick job

Asko dishwasher (D5532) is draining slowly. Issue identified: • Filter assembly / locking ring is broken • Likely blockage in pump area or drain line Scope: • Remove damaged filter assembly • Supply and install new filter assembly • Clear any blockage (pump / hose) • Test unit is draining properly Photos attached.

Clean fan and light fitting

Connect new washing machine and make hole bigger in cupboard for power cord

Currently there seems to be no power running to the dishwasher - it won’t switch on. I will need someone to try to troubleshoot it and hopefully get it back up and running again. Thanks.

Try to run a program and comes up saying hot. AI has suggested this 1. Faulty temperature sensor (thermistor) • The machine thinks it’s hot when it isn’t • Fails safety check → aborts every cycle 2. Dryer heater relay stuck “ON” • Control board thinks heater circuit is active • Machine shuts down immediately for safety 3. Control board fault • Common on Samsung washer–dryers once they age a bit

Licensed plumber required for the installation of new gas cooktop. 600mm 4 burner. Gas to unit is off, existing lines as pictured. New unit product code- the hood guys: GGSCG6004. Compliance certificate required upon completion.

I have a Tudaloo Pro (WaterMark and integrated backflow prevention) bidet seat that needs installation. Need a licensed plumber to issue a certificate of compliance. Wet area GPO already installed.

Removal of old dishwasher and installation of new one. If possible disposal of old one as well but not mandatory

We recently have decided to change our front doorbell from a conventional camera and doorbell system to a google doorbell that allows us better integration. There are exisiting main wires from the previous camera already coming out of the wall. We are looking for an electrician to wire in the camera to allow us powered 24/7 security rather than the battery currently. We are wanting to cover the wires with the camera. We can either figure out a way to hide previous screw holes with your advice or we can sort this ourselves at a later stage.

Heir washing machine having leakage from bottom

Need gas hob switched to a new one. I have new one and old one still connected.

The shelf that the range hood is attached to has come away and needs to be screwed back into place. The range hood itself is fine and there are no electrical or other works required for the range hood.

Can't get brew pressure high enough despite adjusting pressure relief through its full range of movement. And the pressurestat adjustment is too high, and, again, I can't seem to change it despite turning the adjustment screw. Finally, the machine is taking too long to start extracting coffee -- some 20-25 sec after raising the control lever.

Repair dryer that is wall mounted

Hi there, washing machine is not happy, no matter what setting I put it on makes noise but no water, soon etc