Find a reliable appliance technician in Coburg

Looking to install a new feed for an electric oven (15 amp) & an induction hob (32 amp) so I can remove gas appliances.

Replace an old rangehood (Coburg North) and install 2 new bathroom exhaust fans (Fawkner) in Single-floor old houses. The old rangehood is not working anymore. We bought the same one to replace it. Just need to install. The exhaust fan needs to have a hole made; there is a light and switch in the bathroom. You can connect the cable to it. The two houses are only 4 minutes away from each other. Very close.

Cap the copper gas pipe currently feeding a gas oven.

Gas has been disconnected but I need heater removed and disposed of

The old rangehood is not working; we bought the same one already, and need to install it. (Coburg North) We also need to install 2 exhaust fans in the bathroom. ( Fawkner, just few minutes away from the Coburg house) Single-floor house.

Smeg dishwasher heating element not working.

Smeg diswasher heating element not working

Looking for someone to reconnect and properly secure a washing machine drain hose under the sink. The hose is not tight connected so its may need a par to connect it or I dont know you can see from photos the grey hose. Should be a quick job.

Wanting a gas plumber or someone with experience with this type of heater to remove the old gas heater from fireplace, and then restore original fireplace, we are unsure what we are left with once the heater is removed. Have already had a gas plumber confirm the heater is not connected.

We need the braided pipe and backflow filter for a bidet installed. Require offers from licensed plumbers so that we can ensure our bidet warranty is not invalidated. The bidet comes with the required flexible pipe and backflow valves. The pipe going from shut off tap to the cistern is a metal pipe (shown in images) and weve also bought a new flexible braided pipe to replace that with if necessary as part of the installtion in order to add the bidet pipe/valve. Should be easy breezy. Open to offers

Please see attached photos. The cabinetry at the top and bottom of the dishwasher has come apart. The screws that stabilise the dishwasher have come out so the dishwasher falls forward when you open it. Experienced cabinet makers (or similar) only please. I’m looking for someone who has specific experience with built in cabinetry repairs. Thanks!

Need this old/unused gas line cut and capped at floor level. Gas has been turned off at the meter for 6 months (not abolished). Everything is now electric.

Cabinet Modification for Full-Size Dishwasher Installation Looking for a cabinet maker or handyman to modify our existing kitchen cabinetry to fit a standard full-size dishwasher after our current dishdrawer finally died. The job: * modifying the existing cabinet e.g removal of shelf underneath DishDrawer *cutting the cabinetry and kickboard as required to create the opening for a full size or skinny dishwasher (full length) * Ensuring a neat, professional finish ready for dishwasher installation. Measurements are: H: 87cm (floor to black countertop, incl kickboard) W: 59cm (internal cabinet wall to cabinet wall and width of current dishdrawer) D: 56cm (measured to back wall of adjacent sink cupboard) Kickboard H: 10cm

-Change over 2 Gang Switch. Screw Back Fallen Over Powerpoint and Mount Block on Brick Wall. -Disconnect and Remove Old Rangehood. -Fit New PowerPoint and Install New Rangehood (Client supplied) Provide Non-Prescribed Electrical Safety Certificate.

Remove and install 60cm slide out rangehood. It's a plug in so no electrian needed.

Remove electric heater from wall. Connected with steel bolsters. Unsure of screws required

Seeking repair of Fisher & Paykel DishDrawer which has started malfunctioning. The dishwasher has stopped working, keeps beeping and trying to go to rinse cycle with no water. Flood protection seems to be triggered thinks there’s water in the base pan and is trying to prevent a leak, and cannot get the machine out of the kitchen cabinetry as fixed.

I just want my old gas heater disconnected from the gas, because my son is temporarily sleeping in the lounge room and I'm worried about a possible gas leak

Quote for Looking for an experienced carpenter/handyman to modify an existing kitchen cupboard section to create space for a dishwasher. Scope of work: Remove internal shelves from current base cabinet Adjust/modify cabinet to fit a standard dishwasher Cut access holes for water hose, drainage and power Ensure cavity is level and suitable for installation Height (mm) 845 mm ,Width (mm) 598 mm, Depth (mm) 600 mm Please bring your own tools.

Current cavity for oven is about 1170mm high and we are replacing with new oven that’s around 890mm high. Want a filler panel and shelf for bottom of cavity to make sure oven appears snug in cavity. White gloss melamine finish for filler panel.