Find experienced local tradies in South Brisbane

Roofing/flashing repairer required to inspect and repair water ingress issues in 3 areas of a house/carport. To address the source of water ingress, reseal/waterproof the affected junctions, and replace any locally damaged fascia/trim where required. Large-scale replacement works are not expected unless clearly necessary. Part A – Carport corner/pillar Water appears to be entering the corner above the brick pillar, causing the black fascia/trim board to rot, with staining/runoff down the pillar. Required: Inspect and identify likely entry point Carry out targeted resealing/waterproofing of the junction/flashing Remove and replace the damaged section of fascia/trim if needed Make the corner watertight Part B – Front awning/patio roof Leak where the metal awning roof meets the house wall. Required: Inspect roof-to-wall junction Reseal flashing/joints as needed to stop water ingress Part C – Rear awning/patio roof Similar issue to Part B, but along a longer section. Required: Inspect leak points Carry out targeted resealing of flashing/joints as needed Ensure water is draining away correctly Photos attached. Please quote for the repair work needed to make the affected areas watertight. If any larger replacement works are considered necessary, please explain why and provide that separately from the base repair scope.

Paint Bulkhead rendered blue board and patch and paint the soffits under. Will supply paint.

need to clean prepare the blueboard (James Hardie) the blueboard was up and installed in Jan 2026 will need primer then rendering of the wall total area about 22.5m2 2 side wall of 2.2m (H) x 1.8m (w) 1 long wall of 2.2m (H) x 6.6m (w) please provide quote, number of days/week needed. please advice when would you would be available to get the job done. happy to pay after all the work is done.

Correctly plug hole with plaster and small paint over 50cm x 10cm strip where old light fitting used to be

Fix or replace a wall power point in my kitchen Reconnect the power back from the switch board Also look to replace 2 ceiling fans controllers if under my budget. Please quote. See the photos as references Got it done the sooner the better

I need to replace Gyprock sheet to FC sheet. Wrong material for splash back was installed. Need 2 cut outs for GPO

PLEASE DO NOT MAKE OFFERS FOR QUOTES! The price you offer is to complete the job. Thanks - Ceiling needs to come down. - baton out ceiling (I have the batons). - install new sheets and set ceiling with laser. - install 2x ridge joining through the ceiling. - set and cornice. - you will supply and install sheets, cornice and apply all coats. Dimensions 3550 x 3330

I would need this section rendered

One of the pivot screws has broken off and requires a replacement. This part pivots the awning up and down once its been extended out.

Need a handyman to fix, sand and paint two small holes on the plasterboard wall.

I need to put 5-6 power point

$250 for first point including call out fee. $150 for additional points. We will work with you on practical locations..

Scrape down and apply two to three if required coats of acrylic lowsheen woodland grey to stairwell, screens and balustrades, no filling just coating, no overspray or drips anywhere else. Ideally nook and cranny roller and brush, materials supplied. Two gates, road side only

Put up a metal house sign approx 1 m long on a newly rendered wall and 2 metal numbers on a tiled wall.

SEEKING PLASTERER WITH PAINTING EXPERIENCE. Need a Plasterer to complete a 3/4 finished Reno job that my sick tradie is unable to complete by Sat 31st Jan. Following to be done. -Complete another layering on 3x bedroom walls -finish plaster work and paint to completion (bedroom, hallway, kitchen)

Plastering required to patch 2 holes which were cut out of the plaster board to repair water leaks. Square setting. Hole 1: 1200 x 600 (approx) Hole 2: 600 x 200 (approx)

A licensed electrician required to add power point as marked in the photo.

I took out the medicine cabinet in bathroom wall and tried to fix the hole myself with gyprock and filler. Continues to show cracks around the edge. Need someone to fix this for me, so no cracks are seen when painted over. I have some spare gyprock to use if needed.

Recently got a internal wall built. Wall is 3.8m long. Want it to be patched, painted and sanded in a small area. Also want a patch and paint job also in an anoyher area in the house

An experienced and good renderer required to patch up some cracks on exterior of house and walls. Photos attached. 1. Small crack on exterior of house. Textured finish 2. Corner of block wall - had cracking and painter attempted to silicone, but looks shit. Good renderer to repair and prep for new paint 3. Crack on render wall