Find an experienced door installer in North East Melbourne

Looking for an experienced handyman or carpenter to install a Canopia Sophia awning (1.6m x 0.9m) over my rear door entrance. Awning materials & assembly instructions are supplied in kit. Will need to bring own tools & appropriate heavy duty timber screws, washers & weatherproof sealer. The awning will be attached to 50mm (approx) thick timber, which sits behind grey mini orb cladding. Happy for the awning brackets to be neatly pre-drilled and mounted using standard spacer sleeves/washers to keep the mini orb flat.

Pick up a Door from Bunnings and Install door

1. Replace 5 Door Handles Remove 5 existing door handles and replace them with new Ikonic Sira Matte Black sets (1 x Passage Set, 3 x Privacy Sets, 1 x Entry Set). Note: The existing holes in the doors are smaller than required for the new locks. Appropriate tools will be needed to enlarge and adjust the door holes to fit the new hardware securely. 2. Relocate/Fix Towel Hook Remove the loose towel hook. Drill a new hole to securely mount the hook into a sturdier position. Fill the previous hole neatly with plaster/filler. 3. Repair and Fix Toilet Paper Holder Remove the loose toilet paper holder. Fix the damaged/cracked plaster. Re-secure the holder so it is firm and stable. NO PAINTING REQUIRED: You only need to do the plastering/filling work. Materials Provided: I have all 5 new Ikonic door handle sets ready to go. Tools Required: Please bring your own tools, including hole-enlarging tools for the doors, wall anchors, drill bits, plaster filler, fibreglass sheet and sanding equipment.

install a door lock and a hinge

Thin wire inside the rubber door seal of the front loading fisher and paykel washing machine keeps coming out and the door does not get properly closed.

INSTALL DOOR FOR 1 OF THE ROOM

External laundry door needs 2 to 3mm planned off top and side, Door frame is wooden with existing three hinges. need to fit the door with deadbolt and a door handle and hung. Location is Mernda

I need someone to change the doorknob on a bedroom door and bring a drill as well as I don’t have one

Looking for an experienced carpenter/handyman/builder to design, source materials for, and install a custom sliding barn-style door inside my single garage to close off a large open wall section. I’m looking for someone who understands this type of build and can manage the project from start to finish, including sourcing all required materials, hardware, brackets, tracks, framing, fixings, etc. I do not currently have any materials purchased. Existing Space Total wall length: 6.4m Garage opening width: 3.47m Door to be installed on the inside of the garage Existing garage structure and wall shown in photos Design Goal I would like a modern barn-style sliding door that: fully closes across the opening when the garage isn’t in use slides open partway when access is needed For aesthetics, I would like the front of the door clad in: Ekodeck 219mm Hazlewood Batten Screen Castelled Panels from Bunnings (or similar if recommended) The finished look should feel warm, modern and architectural rather than industrial. Important Considerations Installer will need to assess: spacing around existing garage door tracks/brackets ensuring the panelling can sit flush and neat structural support for the weight of the door and cladding smooth sliding functionality weather resistance and durability best mounting/framing solution weather sealing or locking mechanisms are needed Budget & Timing Looking to have this completed ASAP Budget is approximately $1500 including materials, so please only reach out if this is achievable within budget.

Dog door installed for wooden door

I will have the door and hinges provided just need someone to come trim and install the door

I would like to replace the old square deadlatch/deadbolt with a handle style yale smart lock (already purchased). Door frame might need to be replaced too by the looks of it.

I am after getting a new, unmodified exterior door installed in place of an existing door. On top of this, I would like to get a doggy door installed on the new door. I am able to provide the materials (see picture). The hardware/fittings of the previous door must be transferred to the new door. This includes a knob and a deadlock. The door measures 2040 x 820 x 35. At the end of the work, there would be a new door installed, which includes a doggy door. Price is fairly flexible.

Installation of dog door with toughened glass in sliding timber door. Dog door will be provided. Measurements 57Hx81W.

Have an office area and we have cut a door area for a door 2mx1m. I will supply door but need someone to make a frame, fit door on hinges, fit handle and finish gyprock around door and fit skirting.

Hi, my bathroom door is inswinging, I want it out swinging. Its pretty straight forward job for someone who is experienced. Thanks

Total of 9 Door stoppers and 6 glove box holders to be installed. Door stoppers installed on metal doors. Glove box holders to be installed on tiles. Metal doors will require previous door stops to be removed. The holes will need to have silicone applied to them.

Need someone to install a heavy duty rubber or silicone door sweep under my basement door. The gap is letting in alot of leaves and lizards and it needs to be fixed. It's also on an angle so that needs to be considered

Hi there, I’m looking for a handyman to install a dog door on an existing door. The door is already installed and will need to be cut to fit the dog door. Details: • Existing door (already installed) • Cutting and installation required Please let me know your availability, an indicative price, and any relevant experience or examples of similar work. Thank you.