Find trusted local electricians in Sydney Eastern Suburbs

I have a Rheem Stellar 315L(model 4A1315M8) currently on an AGL Controlled Load Circuit. I need a LEVEL 2 ASP to completely disconnect it from the off-peak meter/network ripple relay, submit the network abolition paperwork to AGL, and rewire the tank into my main general house consumer mains circuit. Please instal a DIN-Rail Digital Timer and Switchboard Contactor set to run the tank only between 10.00 AM and 3:00 PM so it can run off my Solis/Fox ESS Solar setup.

Looking for a licensed electrician to install smart home wiring in one bathroom. Scope: 1. Replace existing light switch with a no-neutral Zigbee relay (e.g. Sonoff ZBMINIL2) — need to confirm if neutral is available at the switch or ceiling rose. 2. Wire a separate Zigbee relay for the exhaust fan (currently on [timer switch / isolator — TBC]), ideally on its own circuit from the light. 3. Replace/add a double GPO powerpoint (smart-compatible, not required to be smart itself). 4. Confirm bathroom circuit split complies with AS/NZS 3000 (lighting vs GPO circuits) — flagged by a previous electrician as an issue with a combo touch switch/GPO product I’d originally chosen. I’ll supply the Zigbee relay modules and sensors myself. Need someone comfortable working with low-voltage smart switches alongside standard AU wiring. Ceiling/roof access likely required to check neutral availability. Please quote based on an inspection first if scope is unclear. May be others to install after this too

We have 2 person sauna that needs electrical install. There is a current electrical connection that previously powered spa which we believe will adequate power.

We have an existing light and power point that need to be moved. See picture.

Change over light fitting and wire in Flexible for time/day

Need two replacement fans with integrated lights installed

I need a fully licensed electrician to install a new power point in my garage, run from the main switchboard. Scope of works: • Install 1 × double GPO in the garage • New circuit run from the main switchboard, fed from the unit meter • The main switchboard is outside the garage, in an external position — the run goes from there, along the exterior, and into the garage above the door opening. No drilling or wall penetration required. • All cabling to be concealed in conduit for the full run. • Approximate run length: 13 metres • Supply and install all materials

Looking for a licensed electrician to remove an existing pendant light and install a new single pendant light in its place. Job Details: Scope: 1-for-1 pendant replacement. Disconnect and remove current light, wire and mount new pendant fixture. Ceiling Height: Standard residential height (~2.4m – 2.7m). Materials: All new parts are on-site and ready to go (shade, cord/socket, ceiling canopy, and mounting bracket). Requirements: Must be a qualified, licensed electrician.

We have two ceiling lights that have never turned on and we want to assess whether its just the bulbs or a wider wiring issue. We need more light in this room so ideally want to change the ceiling bulbs and shades but currently have these very heavy, dated covers attached. Initial fee is for callout and assessment and we can negotiate total cost when we know what the issue is

Due to some wiring issue in a large apartment building, the bathroom light is on constantly. I need a second opinion on what’s going on which may require investigation of other rooms (removing and putting fans back on). Need a very experienced electrician to solve this problem.

I need 2 x light fixtures and cords changed. One of them requires a ceiling hook

Screw in 3 light switches 1 power point 1 light

I’m looking for an electrician who is available to come to Bondi in the next couple of hrs. The electricity in 1 of the units keeps dropping. I believed it was caused by overseas tenants plugging in something not compatible. We have put the twitches up in the sub-board but the drop again.

One of the inserts of my power socket appears melted. Need to make sure it is safe and if anything needs replacing.

I am looking for a licensed Electrician to install a double GPO for me. I will be installing a ceiling mount tv. Surface ducting is perfectly fine, there should be a gpo nearby to piggy back from. That is all that is required nothing else. Piece of cake to a. Professional. I’ve enclosed a couple of pics as examples to the type of environment we will be working in. If the job goes well then I have about 10 more sites for the successful applicant. So don’t just think about this job alone but collectively this could be a good earner.

Our laundry cupboard fan stopped working. It is only 8 months old. It stays on a little longer after the light is switched off, or the dryer, I can’t recall which.

Looking for a licensed electrician to fix electrical fittings after an internal wall demolition. I need the following reinstalled and connected: Refix 2 power points. Refix 1 light switch. Test the circuit and confirm everything is working correctly. Ensure all work is compliant and provide a Certificate of Compliance if required. The wall is already open, so all wiring is exposed and easily accessible. No wall chasing or demolition is required. Located in Bondi Junction. Please quote including labour and any minor materials required. Licensed electricians only.

I need an electrician to replace a light pendant in a bedroom. Attached are photos of the old pendant and new pendant that I have bought to replace it. Ideally can come tomorrow either before 9am or after 12pm

My phone line and tv antenna outlets work as far as I’m aware, but they are very old/yellow and I would like to modernise them. I would like the tv antenna one to also be slim against the wall if possible, not currently in a big box how it is.

I need two ceiling lights fitted (one in pantry and one in wardrobe) And also replace an outdoor electrical socket with a double one. Also would like for a power cord from irrigation controller to outlet be cleaned up (notice the glue and hanging cable) I have the lights and the socket already