Find trusted local electricians in Rose Bay NSW

Looking for a licensed CEC-accredited solar electrician/contractor to re-route and rewire an existing rooftop PV array between two duplex properties. Current Setup: Left House: ~6kW Trina solar panels connected to a Fronius Symo 10.0-3-M Inverter. Right House: ~11kW Trina solar panels connected to a Fronius Symo 10.0-3-M Inverter. Scope of Work: 1. Disconnect and re-route the DC string cabling from the ~11kW Trina panel array on the right house roof to supply the left house. 2. Reconfigure DC inputs/MPPTs on the left house’s existing Fronius Symo 10.0kW inverter to integrate the additional capacity safely and optimize performance. 3. Perform necessary testing, commissioning, and safety checks on the modified setup. 4. Update and issue compliance documentation (Certificate of Electrical Safety / CEC Compliance Certificate).

Move 2 powerpoints and 1 six gang switch. Double brick wall. Blue tarp is an opening needs to keep open will likely need to go up around into timber floor joist ceiling. Photos attached. Looking for electrician to do whole house renovation also.

Looking for a NSW-licensed electrician to install two new double power points in our apartment in Rose Bay. The walls are concrete, so we’d like the new power points surface mounted, with any visible cabling neatly enclosed in white ducting/trunking rather than cutting into or chasing the walls. The new outlets will be located as shown on the attached annotated floor plan, with an existing power point nearby. The approximate distance from the existing point to the new locations is 4–5 metres. Looking for the job to include supply and installation of the two standard white double power points, any required cabling, mounting blocks, ducting and other materials, along with testing and the relevant compliance certification. Please only make an offer if you hold a current NSW electrical licence.

Replace ceiling light fitting.

I need a licenced electrician to move power point 10 cm to the left on a Gyprock wall, another removed from the skirting of a built in wardrobe and two landline phone points removed. Photos in order below.

Electrician to install a hanging light to ceiling. Take current light down and install new. Refer to photos. Located in Rose Bay Flexible with day/time

Power points, dimmers, etc

I’d like to have a pendant light installed on the living room ceiling with a light shade. I already have the light shade and pendant cord (pictured). Please refer to the image of the current light and the final look (middle image) I’m after.

instal solar panel for camera

Needing an experienced electrician to install a hanging light it’s approximately 8 to 10 kg and is replacing a ceiling light. Location: Rose Bay Flexible on date/time Thanks!

We need to replace the existing working outdoor light fittings with new ones in photos

I have a surface conduit that is hiding electrical cables that operate my light. One in the sunroom and one in the kitchen. I’m open to suggestions but the easy fix may be running the cables behind the brick (in the cavity). I basically want a clean finish where I have a light switch and nothing else visible. Happy to move the plug if that makes your job easier too.

I need to replace kitchen down lights that can be accessed from the attic and are hot wired to the switch, I can supply the led replacement or have you source them.

There’s a light fitting over the dining table and a light fitting over the kitchen bench. There maybe light bulbs needed which I’ll investigate further. The fittings are already there from previous lights.

I need my electrical powerpoint in my kitchen moved upwards by 7cm in order to fit my fridge inside of a cabinet.

Hi, Can you give me a quote for Level 2 electrician to: - disconnect existing old analogue meter box and delete AC - install new smart meter box in main switchboard in driveway - intercept existing underground cable and connect to sub board - no need to fix driveway afterwards. Dig up pavers on sand no concrete. Please see photos attached

I need a licensed electrician to install a new flush DC ceiling fan. • There is currently a lighting fixture in the space, I’ve already loosened the nuts and bolts. • The new fan (already purchased) needs to be installed in its place and connected to the existing lighting circuit. • Wiring must be safely connected to power and tested. • Fan should be mounted securely and working correctly. Please bring all necessary tools. Must be a licensed electrician.

I have a lamp and a clock radio from Europe that needs to change its plug to fit Australian socket.

Garage in apartment building. Main garage has a disused light fitting with switch on wall. Might just need a new fluoro but want the fitting and switch checked. Side room has a potentially broken light fitting where an existing globe was firmly knocked out. Needs new fitting/wiring and new globe. Might be very straightforward for both items but need someone to take a look.

I’d just like 4 down lights changed in my kitchen. I’ll purchase the new bulbs. They’ve just blown