Find experienced local carpenters in Elizabeth Bay

Hi. I am looking to repair a couple of spots on a window frame before I paint them. I have attached some photos below. Thanks.

I need 5 built-in shelves installed inside my wardrobe. White colour 4 of them ~ 56*56 cm 1 ~ 30*56cm

Involves drilling into bathroom tiles with caution, and hanging new cabinet on the wall. No pre-assembly needed.

Modify existing bottom hinged cupboard door in laundry to make into two standard hung doors. Make new trim piece around microwave and toaster shelf.

Build a custom cabinet under the window in bedroom

Must be completed by 8:30am Saturday. Tools needed. No assembly instructions have been provided so would be ideal if you have experience putting together stainless work benches or commercial kitchen benches

My door slammed and the glass smashed in some places.

We are finishing the renovation of a flat and need a hand with some small carpentry tasks for a high end finish. Floor board and ceiling trim and door hinges so that French doors open outwards

As per attached photos existing cabinetry to be altered to fit larger fridge fridge size 17 20 x 700 x 700

I need to fix some artisanal wooden masks on my wall but it needs to be drilled. They are 6 of them, one hole each would be enough. Really quick job for this, I just don't have the equipments to do it. Can be done after 5:30pm every weekday or this Saturday morning. Thanks

I managed to get a stain on our wooden dining table due to flowers falling on to it. We've tried cleaning the spot and buffing out with a dremel then polishing with beeswax, to no avail.

I tried to fix an olive oil stain on my American oak dining table using bicarbonate soda paste followed by lemon juice and I made it soooo much worse. I need a skilled carpenter to sand it back and repair, keeping surface as even as possible. Can you help?

Have two doors that cannot close One is very large and the other is laundry door. Both have swollen and need to be adjusted or sanded to fit

Tasmanian Oak hardwood panels from an inbuilt wardrobe to be collected. Most panels are 2.5m in length and could be used for carpentry projects. Will pay $80 for it to be collected.

I have a wooden bed frame that has sustained damage. The corner joint where the side rail connects to the footboard has come apart, causing the frame to lose stability and support. I need the frame to be repaired so that it is stable and can support the mattress and weight without collapsing. - Due date: Flexible

Measure exiting drawers space for single drawer dishwasher where there is no existing dishwasher, advise on cabinetry - removing existing drawers to insert new dishwasher , advice on electrical and plumbing connections useful - Due date: Flexible

I have a "study nook" that I need some specifically shaped wood for the top. I've already cut a large piece of card as a cutout to map the position (see photo).. Need someone to collect my cutout (from Elizabeth Bay I'll run it out to your car), grab the wood, do the cutout and deliver back. I do not need this Installed, I can do that - just need the wood collected, cut and delivered back to me but will need a hand to carry into building. Want a beveled edge on the outfacing side only. Want tasmanian oak. Should be finished but not stained as I will stain it. Should be 1- 1.5 inches thickness at least so there is limited movement. Would like this back by Wednesday night this week. Fee is for the work - I will reimburse the full cost of the wood on receipt - Due date: Before Wednesday, 1 November 2023

Hello! Ignore the $500 price, you tell me what it will cost once I give you specs. Sydney job I’m replacing the old 20mm wooden benchtop on my 1950s kitchen. There are two panels needed, which I will draw up for you (I’m an interior designer). What I need you to do is order the Laminex panel, cut to size and apply ABS edging. I know the exact Laminex colour/finish I want, and I’ve checked that it comes in 18mm. You don’t need to install it! My builder will do that. - Due date: Flexible

I need a temporary timber railing to be designed and built to raise the existing balcony balustrade to BCA required height as protection for guests at a party. It cannot be fixed into existing surfaces and must be self-supporting both structurally and functionally. The attached photos are one idea, but I am open to better ideas! On the photos, the blue lines represent an option to lash the structure around the central balcony pillar to provide additional support. The successful applicant will attend site to discuss and measure, then provide a hand drawn shop design. Once approved, they will source and supply agreed materials, and will undertake construction, providing protection as needed to existing surfaces and clean up afterwards. The quoted price should include an estimated PC sum for materials, but actual materials will be paid for at cost. - Due date: Before Thursday, 20 July 2023

Give me a quote, and I'll update the task. I need someone to do these tasks: Change the fronts of 2 drawers and a door of a cabinet. They're all Polyurethane. The drawer fronts are 190x175mm and the cabin door is 400x410mm. (Photo 4) Create and install 3 Polyurethane shelves. Two of them are 550x350mm with two rounded corners (Example in Photo 5) and one is 300x170mm with one rounded corner. Patch a few holes and scratches in some wood and polyurethane drawers/shelves (examples in Photos 1,2,3) Change the side runners for 2 drawers - Due date: Flexible