Find a fence installation professional near you

Install approximately 10 x 2000mm posts 500mm into the ground for a future front fence. I will supply the 100x100 posts and quick drying cement.

Shared wooden fence with neighbor is leaning towards us. Need someone to either fix this or replace the entire panel.

I am selling my house and would like to spruce up an old fence. The dimensions are 3metres long and 1.5 metres high -Perhaps even make some covers for the prominant gas meter/water meter- wood -

Need a double gate installed to gain access to the back yard

Looking for a few quotes to replace this fencing - or repair it. Quote to replace with either timber or colourbond. 8.5m long

To install privacy fence

Replace an existing wooden fence in front yard

Looking for an experienced fencer to supply and install a new timber picket fence for a residential front yard. Key Details: Total Length: 13 meters (straight run). Current State: No existing fence (clear ground). No demolition or removal required. Gate/Door: Not required. This is a single continuous fence panel/run. Style: Timber Picket (please refer to the attached photos for the specific picket profile and spacing). Finish: Looking for a professional finish to match the style/color shown in the images. Scope of Work: Supply all materials (posts, rails, pickets, and concrete). Dig post holes and set posts in concrete. Install rails and pickets to a high standard, ensuring the line is perfectly level. Site cleanup upon completion. Site Access: The site is in Blackburn. There is easy access to the front of the property for delivery of materials and equipment. Please include in your quote: Estimated timeframe for completion. Confirm if you can match the style in the photos. Whether you provide a warranty on workmanship.

I need someone to come measure my gates and grab anything that fits and is sturdy and replace gate will cover expenses ontop, need done asap as have large dogs gate has to be able to hold them in there lay the challenge the gate below failed

I have 3 outdoor gates that all use sliding pad bolts to close/lock. The gates have moved over time and the bolts no longer lineup properly to close (at least without applying force). Two of the bolts are fixed to a steel frame, the other is directly in the timber door. The bolts all slide into concrete posts (see photos). Not sure if the bolts themselves just need to be moved slightly to line up with the hole again or if we need whole new pad bolts put on. I don’t have the correct tools to do myself. Will pay for any materials needed.

I have a metal side gate where the latch/bolt goes into a brick wall. The brick has worn out and been patched previously and the bolt can now be forced out, wearing away the brick. I need a proper, long-lasting fix. I believe we need to drill into the brick and install a steel receiver/sleeve (tube) for the bolt or something similar to fix the issue. Open to other ideas!

Looking for someone to install 9 Screenline fence extender panels to our existing fence. * 3 panels need to be trimmed/cut down to size * The remaining 6 panels just need to be installed * We’ve already installed 3 ourselves, so the process is straightforward * I’ll be around and happy to assist with lifting/holding the longer sheets if needed This should be a relatively easy job for someone with basic tools and experience Requirements: * Must have your own tools (including something suitable to cut the panels cleanly * Experience with fence/extender installation or similar handy work preferred Location: Hazelmere, WA Timing: Flexible – ideally completed soon Let me know your availability

Will need an angle grinder to cut the 90mm x 90mm posts to size, and a rotary drill to screw posts into masonry wall. 40mm x 40mm Battens are cut to size already. All gate hardware and screws provided. It uses a rail and clip system similar to the first photo. From Eurowood. Also remove and dispose of existing gate. Estimate it will take one person 4 to 5 hours or 2 people 2 hours. Located Broadbeach Waters

Please quote on installing a gate in these fence panels. My sister lives next door and we want the children to be able to walk back and forth easily.

Need assistance with installing a timber fence. Will mainly be assisting installer on site to install posts and ply. Tools provided.

Fence and gate installation. Timber or colour-bond. Gate side: H1.95m x W2.0m Garage side (4 x panels) H1.95m x W0.2m

Replace the damaged fence extension, budget including new materials

Need a front fence built to match the front balustrade. Rails already installed. We will supply timber verticals and timber for crosses. Will need to cut and install crosses and verticals. Approx 2.7m long total (in two sections). Must be neat and even.

Hi I would like someone to install an under fence plinth beneath the existing colourbond fence to prevent my grass from entering the neighbours property. Length of plinth approximately 1.1m. Preferred colour is grey to match existing fence.

Block pier has been reinstated, just need the one half of the aluminium double gates reinstalled, with new supplied gate hardware, and hinges to be removed from the damaged block pier. 1 aluminium screen to he reinstalled also. Pier was blown over in the cyclone.