Find a reliable appliance technician in Dandenong

I have a hisense refrigerator. Which needs a repair.

Looking for a licensed gasfitter to provide a quote for a gas safety inspection and safety check at a rental property in Dandenong.

Hi, I’m looking for someone to repair/check my gas cooktop. One of the burners isn’t working properly. Located in Dandenong

slide out rangehood install, needs to be screwed in from the top, but cabinet backing is blocking access. Cabinet doors also need to be trimmed by 30mm. Slideout range hood with recirculating and charcoal filters alrdy on hand, no additional ducting

The water keeps getting stuck and not flowing, I am not sure

Need a cabinetmaker to rearrange cabinets to fit room for a dishwasher. There will need to be space to ad power point for the dishwasher and for the plumbing. Right now the cupboard is too small to fit a standard dishwasher which are normally 600mm wide.

Need to place new dishwasher and remove old

Pet cremation facility in Dandenong. Two jobs on our dual-chamber incinerator, ideally one visit. Machine will be cold and isolated. Job 1 — Replace the combustion air fan (mechanical + electrical) • Remove the existing 0.75 kW high-pressure centrifugal fan and fit a larger one (approx. 800–1,000 m³/h at 2.5–3 kPa, ~1.1–1.5 kW, 240 V single phase). We can supply the fan or you can quote to supply it — if you quote, tell us which fan and send the curve. • Adapter flange to the existing riser if needed. Add a tee with a capped stub on the outlet for a future second line. • Fit a gravity backdraught damper and a lockable balancing valve on the main duct. • Replace/upsize the motor starter, overload and cable to suit the new motor. Local lockable isolator at the fan. • Fit an airflow proving switch wired into the burner permissive circuit so the burners cannot run without airflow. • Commission: confirm airflow, prove the switch, test backdraught, run test. Job 2 — Burner ignition interlock • The bottom burner is locked out from igniting above 200 °C by the control panel. Trace and document how this is implemented (XMT-series temperature controller alarm relay, thermostat, or relay logic). • Reconfigure it as an over-temperature trip at 1050 °C in line with the manufacturer's written instructions, which we will provide. Test that the burner enables above 200 °C and trips at the new setpoint. Deliverables: Certificate of Electrical Safety and a one-page record of what was changed and the final settings. Who: licensed A-grade electrician with burner control experience (Siemens LMO / Baltur ideal), working with a fitter for the mechanical side — or one person who does both. Please quote labour separately from fan supply, and tell us your availability. Weekday site access, panel photos and manufacturer correspondence available on request.

Industrial diesel burner in lockout, plant out of service. Commercial/industrial oil burner experience only — not a domestic heater job. EQUIPMENT: Baltur BTL-20 light oil (diesel) burner, 118-261 kW, built 2022. Siemens LMO14.111C2BT control, Suntec pump, Fida ignition transformer. Fitted to a two-chamber animal cremator. FAULT (confirmed by blink code): LMO14 gives 2 flashes — "no flame signal when safety time expires". Burner runs a full start sequence (~27s, LED flashing amber) then locks out steady red. Repeatable. Video available. ALREADY CHECKED: Photocell cleaned, no change. Fuel supply and pump clean, no air. A panel breaker ("hearth power supply") was found off; restored, no change, hasn't tripped since. Likely: nozzle, pump solenoid, pump pressure, ignition electrodes/transformer, or a photocell that cleaning didn't fix. WHAT WE NEED: Diagnose and return the burner to service. Full burner service on site — nozzle, filter, photocell, electrodes, pump pressure, combustion set-up. Machine is heavily ash-fouled and has never had a documented service. Written note of what you found and changed. PLEASE BRING nozzle set, fuel filter, photocell and ignition electrodes. A code-2 call-out with no parts means a second visit and another week of downtime. SAFETY: It has locked out 4-5 times, so there may be pooled diesel in the primary chamber. Please check and clear the chamber and drainage tray before attempting ignition. We have stopped all resets. SITE: Unit 38, 22 Dunn Crescent, Dandenong VIC 3175. ACCESS: Mon-Fri 9am-5pm ONLY. Planning permit condition covering testing and maintenance as well as production. Not negotiable. REQUIREMENTS: Real experience with industrial oil burners and Siemens LMO controls. Switchboard work must be by a licensed A-grade electrician — say up front if you hold this or subcontract. Quote attendance and diagnosis, plus hourly rate for repair. Photos and LED video ready to send.

Task description： We are an e‑commerce brand selling massage chairs (Costway). We are looking for reliable on‑site technicians across Melbourne for future recurring work. ⚠️This posting is for pre‑qualification & quoting only, NO immediate repair job at this moment. Real service orders will be booked separately once customer cases arise. Our workflow: Our factory team remotely diagnoses massage chair faults. Replacement parts will be shipped out by our side to customer premises. YOU DO NOT NEED TO SOURCE ANY PARTS. You attend customer’s home, disassemble, fit supplied spare parts, reassemble and complete function test. Only labour service required. What we need you to provide in your offer/message： Your service coverage suburbs across Melbourne (which areas you can travel to) Call‑out / attendance fee (flat rate for turning‑up) Your hourly labour rate (GST inclusive or exclusive) Previous experience: whether you have worked on massage chairs, share related job references if available Public liability insurance status Requirement: Able to handle heavy furniture disassembly, basic electronics hand‑on work. Both English‑speaking and Chinese‑speaking technicians are welcome. We will shortlist suitable taskers and keep contacts for future real jobs.

A soon important who can help me

Washing machine drink not water

I’m looking for a quote to replace an existing gas cooktop with a second-hand Miele KM2012G. The gas connection already exists and the benchtop cut-out is the correct size. Could you provide a quote for removal and installation please. Thanks kindly, Sophie.

Not draining water. the filter is not clogged though. It looks like there is an issue with drainage pump.

I need a licensed electrician to install the oven. The old oven has been removed already. Oven being installed: Bosch Series 4

remove the old heater and install new one -for ref see pictures

The washing machine is locked, not turning on and clothes are inside

10 minute job/ cheapest quote? I need a new dishwasher installed. No new plumbing, just connect where the old one was. (clamp on the drainage pipe required if you can''t reuse the old one.

Gas Safety check from licenced gas fitter

I have a new dishwasher unit to be installed at the property. Old unit has been disposed already and new toilet seat to be installed, unit can be provided.