Find a professional heating and cooling technician in London

I need to set up some tado x thermostats 8 zones I already have wireless tado x thermostat and receive to turn on and off hot water and underfloor heating, but zones not configured. Also underfloor heating has cold zones that I need fixed

Philip Whirpool Electric Oven and Grill, only the Grill is not heating up.

Come to check boiler, thermostat needs to be change to get hot water, purchase the part and change it. From the pic below the error code is E110. Please get in contact if you know how to fix this problem.

fix my floor heating， it’s making some wired noise, the pressure is fine

Boiler switch needs replacing . I opened the panel and circuit wires seem to be okay but worth checking

install shelf below tv.shelf provided, please bring own tools. remantle boiler cupboard.

Boiler switch broken .i opened the front plate all connections seem intact . Only switch needs changing please

Replace central heating pipework Looking for a qualified plumber/heating engineer to replace all central-heating pipework in my 3-bed house using 15mm/22mm HEP₂O barrier pipe. Boiler downstairs by the front door. Approximately 7–8 radiators. I will supply and fit the radiators myself along with hep20 22mm and 15mm barrier pipe and fittings so the job is to Install the new 22mm flow/return mains and 15mm branches to each radiator, leaving connections ready for me. Upstairs, pipework only needs to go under the middle/dressing-room floor; elsewhere I want it run above floor level and accessible as itll be boxed in Any joins/tees should be positioned where a discreet access panel can be fitted, rather than buried permanently under floors/walls. Please quote for: Pipework installation only Optional price to connect the radiators, fill, bleed, balance and test the system. I have attached the floor plan

I would like this pipework/boiler output boxed in to hide it. It needs to be done in a way that it can still be easily accessed once a year for servicing, but otherwise will be covered up. Ideally done in white to match the walls but not necessary so long as I can paint it after fitting

No hot water and pressure is down.

The entire flat is using the under floor wet heating. The old thermostat is broken. Model number: UFHDIALB I ordered the same replacement. Need to replace it and seal with silicone to make it looks nice. I am available from 7pm on Wednesday. Please let me know your availability. And or if you need more information. Thx

Hello, I need a boiler service certificate for a boiler in my restaurant. I believe the boiler itself is a domestic-type boiler, although it is installed in a commercial property. I have attached a photo of the boiler so you can check. The boiler is working perfectly fine. My main reason for arranging this is that my landlord has asked me to provide a valid boiler service certificate. I would therefore need the inspection/service to be carried out by someone who is properly qualified and authorised to issue a valid certificate. I would prefer not to have unnecessary work carried out on the boiler since it is working fine, but if servicing is required in order to issue the certificate, that is absolutely fine. Could you please let me know if you can do this and how much you would charge? Thank you.

I have checked and is in working order, all the status lights are green which indicate the hive is connected and working and the same for the boiler as we have hot water. However the thermostat still does not send signal to heat up

Hi! I need an experienced plumber or handyman to replace the concealed thermostatic valve element in my shower (Scudo brand). Part: The replacement thermostatic element is already purchased and on-site. Access: The existing shower system is a concealed valve setup. Photos: Provided Requirements: - Please bring your own tools and white silicone sealant will be required. - You must have experience working with concealed thermostatic shower valves. - Please ensure the water is turned off safely, the element is swapped cleanly, and the seal is tested for leaks and temperature control before finishing. Thank you.

Cylinder Heater Maintenance and Repair Currently no hot water at the flat. Heated Element Replacement needed. • We need to install 2x titanium-coated heated elements (we will purchase from Screwfix or any recommended supplier) in our indirect unvented cylinder heater in a 1-bed flat as they corroded. Cylinder Tank Cleaning • We also need to drain the whole cylinder and scrape/clean the bottom of the cylinder tank to prevent quick scaling of the elements. Please let me know your quote and if you can do the job before Saturday or Sunday this week. Any questions, just message.

Have recently had boiler installed and contractor had to cut out a small hole in ceiling for new flue. Need someone to re plaster the ceiling - also open to offers for those who can re plaster and paint in the same day

I have the boiler installed but I need to install the thermostat to control the temperature. The boiler is a Greenstar 4000 and the thermostat is a Honeywell T3.

Boiler Service and Smart Thermostat Replacement I’m looking for a qualified heating engineer to: * Carry out a full boiler service. * Remove the existing old heating controller. * Diagnose why the heating/boiler seems to switch on unpredictably. * Install and configure a new smart thermostat Drayton Wiser Wireless Heating The new thermostat has already been purchased. Please include any required testing and confirm the system is working correctly after installation.

I need a plumber to re-pressurize my boiler and to tighten the bathroom heater as it’s leaking at 8 AM on the 9th July 2026 please. I have guest staying in my flat and the only time they can do is 8 AM tomorrow morning.

You must be a plumber or a heating engineer. Boiler diagnosis completed as follows below and need someone to replace both parts. Parts to be ordered separately and not included in price here. - system pressure was low. I topped up the pressure and reset the boiler; however, the boiler still failed to fire. The appliance was displaying the fault code shown in the photographs provided. I referred to the manufacturer's instructions, which identify this fault as relating to the gas valve. I then contacted the manufacturer directly to confirm, and they advised that the fault is associated with the gas valve and ignition electrodes, with replacement of these components being the recommended course of action. The active fault codes displayed on the front of the boiler provide a clear indication of the fault condition being detected by the appliance, and the manufacturer has confirmed that these codes relate to the gas valve and ignition electrodes.