Find professional heating engineers in London

The valves are quite worn out. Can you please help me clean it and tighten it up? Please feel free to text me with other optional solutions for it. It should have been leaking a bit and looks quite rusting now. Thanks

Install 20 square metres of WUNDA 20mm Rapid Response underfloor heating system. Ground floor kitchen, small toilet and landing. Concrete floor, that has been levelled.

Looking for an experienced Gas Safe registered heating engineer to carry out a full power flush on my central heating system. Property details: 3-bedroom detached house Approximately 8–10 radiators Potterton Promax Exclusive 35 combi boiler Boiler is over 10 years old Plate heat exchanger has been replaced twice due to suspected sludge/magnetite contamination. British Gas has advised a power flush before carrying out any further warranty repair. Please include: Full power flush of the heating system Cleaning chemicals Fresh inhibitor added on completion Cleaning of any magnetic filter (if fitted) Radiator balancing Confirmation/invoice stating a full power flush has been completed Please confirm: You are Gas Safe registered (registration number) How long the job will take Whether all chemicals and materials are included in your quote

a Dreo electronic heater, a foldable clothes airer and a rice cooker

We need a central AC fitted in an office. It has one outside unit and 2 inside unit.

Hi I need a quote for: Drain down heating system. Replace 2 x Drayton zone valves with Honeywell. Replace circulating pump and pump isolation valves. This is a domestic property.

I need someone to install underfloor heating along all of ground d floor, price is not fixed as person would need to come and view in person to provide accurate quote

Looking to have filing loop replaced as leaks when tap turned to fill pressure

Hi looking for a labour quote to fit retrofit underfloor water based heating on the floorplan attached excluding WC and utility room. The existing flooring is laminate/carpet on suspended wood/concrete. Scope of work will require existing floor removal and prep, installation of ufh and also laying laminate on top. Thanks Peri

Looking for a qualified plumber to: • Remove 2 central heating radiators (1x entry hallway, 1x bathroom) • Cap flow and return pipes securely and neatly • Refill, repressurise and bleed the system • Rebalance the heating system after removal • Remove and dispose of the radiators • Leave wall and pipework tidy Standard gas boiler system. Access is straightforward. Please quote total price including labour, fittings and disposal.

Will need experience with heating in bathrooms. Electrical and possibly plumbing.

I have heatmiser underfloor heating one zone receiver come on but no heat provided

Main radiators in the flat are not working, however the bathroom radiators are working.

Underfloor heating in one room is not working. Floors stayed cold, control panels are all working fine. Boiler is only a year old and just had its annual service done, pressure is good and have nothing wrong.

Our heating is turned on and we’ve bled the radiators but they’re not warming up in the basement. All heating is working in the rest of the house

A Grundfos central heating circulator pump connected to an underfloor heating manifold system. Materials used ProWarm™ Multiple Room Water Underfloor Heating Kit Thermostat Heatmiser Slimline ProWarm™ Underfloor Heating Edge Insulation roll ProWarm™ foiled faced in joist/batten system 68sqm

We have a wiki underfloor heater and it has a red light when the heating is on. It is supposed to be because of air trapped in the system, but I can’t locate the bolt to release it. Can someone help?

The heater in the living room is not working. It is not producing any heat despite being switched on and adjusted to different settings. The issue needs to be checked and repaired as soon as possible to ensure proper heating in the living area.

I would like you to inspect an underfloor heating circuit serving a single room. It seems to have a circulation issue. For clarity: The property has a gas boiler The radiators are working normally throughout the house The issue is isolated to this one underfloor heating circuit I would be grateful if you could: Inspect the underfloor heating manifold and pump Confirm the pump and mixing valve are operating correctly Check that the UFH flow temperature is correctly set Check flow, air and balancing Ensure the loop is fully purged of air Confirm the flow rate is adequate for the loop Rebalance or adjust as necessary I'm here tomorrow, that would really be ideal - Loughborough junction

I need a hand installing tado central heating smart system. My old system is Drayton digiset.