Hire a reliable appliance service in West Midlands

I need a washing machine installed at my home. This is just for fitting the washing machine itself, including connection to existing water supply, drainage, and electrics if required. The machine is already on site and ready to install.

Need an experienced tradesperson to inspect an integrated cooker hood (CDA EIN60SI 60cm) that works intermittently (likely wiring/electrical fault). Please quote separately for: Repair (fault finding + wiring fix) Replacement (remove old hood + fit new one) Also need a new extractor ducting hose fitted and the unit tested for safe electrical connection and ventilation.

Pull out old integrated dishwasher & connect original pipes to new one.

I just purchased a new dryer and i need someone who’s well versed to help me install it

There's a new washing machine and need someone to install it. The plumbing connections are already in place — it just needs connecting and testing. Please bring your own tools and have experience installing washing machines.

I think it's a drain pump . I've check and clean , but not sound from the pump. I just want to know if you can fix it or I have to replace with a new one

3 years old Hisense HV603D40UK is refusing to start when pressing the power button. No error code. If I unplug it and try to start it again after 1-2 hours, it will start and do it's job. Slight vibration noise for the first 20 second after it eventually starts, no odd noise after that. I would like to have it fixed, if it makes sense financially.

Converts shower area by removing shower tray, shower and shower doors to install fittings for washing machine

Rangemaster gas hob: 1)Burner (hob) 1 will not fully turn off—flame often stays on and I can smell gas even when the knob is in the OFF position. The knob for hob 1 feels loose but I’m not sure that’s the cause. 2)Burner 2 won’t light properly; if it lights, the flame goes out as soon as I release the knob. 3)The built-in electric ignition seems not to work, so I’ve been using a lighter.

Fit an integrated washing machine door. It needs countersunk hinges fitted

Washing machine water not going out. Filter cleaned but no working.

Hi , I am looking for a specialist to carry out a "ductless-to-ducted" kitchen conversion in my new-build Taylor Wimpey home this February. The current setup is a recirculating Electrolux hood. I am looking for a professional "one-stop" service to vent this externally to a high standard. Technical Requirements: • Diamond Core Drilling: A clean 155mm hole needs to be drilled through the external masonry (brick/cavity/block). This must be done with a diamond core drill (no hammer/chisel) to ensure no damage to the external brick face or internal plaster. • The Ducting: I require 150mm rigid round ducting to be installed through the wall (cut to size). Please do not use flexible foil/hose through the wall cavity as I want to remain compliant with NHBC Section 8.3 standards. • Airtight External Vent: I will be providing a Naber Flow Star GTS 150 (magnetic airtight system) or Luxair automatic airtight system.This needs to be fitted to the external brickwork and sealed with silicone. • Internal Connection: My existing Electrolux hood has a 150mm outlet. I need the rigid ducting connected to the hood motor and sealed using aluminum foil tape to ensure it is 100% airtight within the chimney piece. • Weatherproofing: The duct must be installed with a slight (1–2 degree) downward pitch toward the exterior to prevent condensation or rain ingress. Project Scope: • Location: Kitchen is on an external wall (back-to-back install). • Access: Side elevation of the property. • Timing: feb Could you please confirm: 1. Do you provide the diamond core drilling as part of your service? 2. Are you comfortable installing the Naber magnetic vent system or Luxair automatic vent system 3. What is your estimated lead time and cost for this specific installation? 4. Will you guarantee that my existing MVHR system will not be impacted by the vent and will be airtight I look forward to hearing from you. Kind regards, Anam

Freezer not freezing American fridge Freezer kenwood

Hotpoint tumble dryer keeps on tripping when turning it on for a dry. Model number - H3 D91W8. To have a look into this and why it is tripping, and sorting this out.

Hi, I’m looking for someone experienced with treadmill repairs to replace the motor belt on my Mobvoi Pro treadmill. The existing motor belt has snapped and needs a like-for-like replacement and fitting. The treadmill is currently at my home, so the work would need to be carried out on site. Please let me know whether you can supply the replacement belt or if I need to source it separately.

New oven was fitted as I’ve had my kitchen installed recently. After new oven was installed the main fuse box keeps tripping.

Brackets on the heaters need fixing

Washing machine struggling to spin

I had my cooker fixed as the temperture part was no longer working but now it keeps tripping the electics in my property. No fix no pay. We can negotiate a price once fixed

Just moved into a new house and I want someone that can connect my washing machine so I can start washing with it.