Find experienced local tradies in NSW

I’ve removed the old one. I’ve got all the measurements. Want the roof to be corrugated iron. Want flashing into the wall. Want to replicate the old timber. Have kept old timber. I’ll pay all material costs with receipts. I’d expect it’d take 1 hour to measure 2 hours to buy material and 2 hours to put together.

Moving out of my rental property. I have removed the screws, but the plastic still remains. I tried to plaster over, but clearly it's not great. There are 4 holes with plastic that need removing/filling, and one screw also needing removal and filling.

Hole in wall gyprock wall roughly 20cm diameter. Two triangular holes in ceiling skirt from built in wardrobe removal. Plaster over feature opening in wall approx 1mx1m. Open to offers.

Due to absence of door stoppers, there is a slign damage in the 4 gyprock walls, the fix measurements are Measurement for wall patches 1. 2cm * 2cm 2. 8cm * 6cm 3. 8cm * 6cm 4. 5cm * 5cm

Remove 2x outdoor AC unit of top colourbond awning . Lower to ground safety. Unit will be disconnected and ready for removal.

Need to repair my balcony Balustrade post . It needs to be secured to the brickwork . Wires to be tightened after completion.

Need to render some patches in kitchen for splashback and bathroom

front porch tiles rendered with acrylic render. Materials supplied, labour only. Looking for someone experienced with a neat, smooth finish.

We have replaced the control panel and power supply. The suana is still not turning on. There is no power getting to the board. We suspect the fuse so hopefully it’s a matter of replacing the fuse. The boards in top of the Sauna need to be checked and if the fault still exists please confirm where the fault is. So this job is to replace the fuse and place cover on main box and check it’s safe, if still not working then report findings. *the fuse has been supplied.

Repair 2x plasterboard bulkheads and small patch to rendered walls/skimcoat on one side. Approx 4x 400mm verticals, 1x 5m horizontal and 1x 1m horizontal. Setting and sanding required. Painting not required. All material and tools to be supplied by airtasker.

I need a handyman/carpenter to take down ceiling on my front porch and install timber paneling with edge trim. Size is approx 4.5m x 2m. We will supply the materials.

Repair gyprock and paint it same colour as the rest of the wall

Need a gyprocker to fix all these holes in the walls of our basketball facility. Open to offers

Hi we need a gyprocker to repair two holes and some small extras like ceiling cracked in photo. It's an Airbnb so the guest needs it fixed asap please if can come today Please fully finished inc sand and paint. It is Dulux vivid white walls Thanks

Looking for a licensed electrician available today for a quick job in Botany. All fittings are supplied and on site. Job 1: Ceiling light replacement (x1) • Remove the existing twin fluorescent batten fitting (cover and tubes already off, wiring exposed) • Install the supplied SAL Decord SL2112/40TC LED Oyster (30W, black, dimmable, IP44) Job 2: Power point replacement (x2) • Replace 2 existing grey/silver double power points with the supplied Deta X6 Series Matt Black double power points (quick-fit base) • Same-for-same swap, no new circuits or relocation Requirements: • Must hold a current NSW electrical licence (please include your licence number in your offer) • Must be available to complete today Photos attached of the existing batten, the new light and the new power point.

When I flipped the power point button off, the lights did not turn off. Top right corner of the switch not working. Other 3 are working. See picture attached

It is a portion of garage wall with 2 small windows

I have around 10-12 large pictures I would like to hang on a gyprock wall. I don’t have the bits to hang them so u would need to supply aswell.

I need a Power Point installed in my 'office' wardrobe by an electrician Refer to pictures

Fix gyprock wall. Paint provided