Find a professional downpipe contractor in VIC

I have noisy downpipes. Looking to put chains or ropes down to mitigate the noise of water dripping. Double storey house, 5 down pipes.

Looking for someone to connect a rain head and connect a downpipe . All material on site .

I have a downpipe issue at my house that needs repair. The downpipe is not properly connected to the stormwater pipe at the bottom * There is a visible gap and water is leaking onto the concrete

Downpipe Dripping Noise Fix Location: Beaconsfield Upper VIC 3808 Height: approx. 3.1 metres I’m looking for someone experienced with downpipes, roof plumbing, guttering or neat exterior handyman work to fix a loud dripping noise inside a metal downpipe bend. The issue is water dropping into the lower bend / elbow section and making a loud tapping sound. I already have rubber material that can be used to dampen the noise inside the bend which I have done elsewhere. Looking for someone who can assess the cleanest way to fit it properly. It will involve carefully loosening or opening the downpipe bend, possibly drilling out and replacing rivets if needed, fitting the rubber neatly inside the impact area, then securing and sealing everything properly again. I don’t want a rough patch job, visible mess, loose metal, blocked water flow, or silicone smeared everywhere. Just looking for someone practical to get the job done. Photos attached so you can see the area before quoting. Small job, but I want it done properly.

Scope of Works 1. Install Gutters * Supply and install 2 x gutter runs * Length of each gutter run: 5.4 metres * Total gutter length: 10.8 metres * Gutters to be installed along the two front-facing roof edges shown in the attached photo (marked in red). * Ensure correct fall towards the downpipe location. * Include all brackets, joins, stop ends and fixings. 2. Install Downpipe * Supply and install 1 x downpipe * Downpipe length: 2.4 metres * Downpipe location shown in the attached photo (green line). * Connect gutter outlet to downpipe. * Discharge to existing stormwater connection if possible (please advise if additional work is required). 3. Finish * Remove all rubbish and offcuts. * Ensure gutters are level, secure and watertight. * Silicone/seal all joins as required. Measurements * Gutter Run 1: 5.4m * Gutter Run 2: 5.4m * Downpipe: 2.4m * Total gutter required: 10.8m Materials Please quote: 1. Supply and install included, and 2. Labour-only option if I supply the materials. Photo Reference * Red lines = new gutters (5.4m each side) * Green line = new downpipe (2.4m) Looking for someone experienced with Colorbond guttering who can complete the job neatly and advise on the best gutter profile for the structure.

Repair roof tiles, fascia , clean gutters etc

1)Removing old Gutters of 1 story tiled unit and replacing with galvanised Gutters approximately 40m around the unit and fixing of 3 galvanised down pipes.Materials will be provided. 2)Fixing the 150 mm Bunnings range hood vent on the tile roof marked in "X" location.Only need to fix the roof end .Vent kit will be provided as shown in the picture. Need to fix it without any leaks 3)Need to remove old and replace with new garage roof sheets,as shown in the picture.Dimensions 5.8mx 2.6m.Need to replace/ re afirm 4 supporting posts and one behind vertical timber support on the brick wall.Materials will be provided.

Downpipe is located on roof. Diffuser required to limit water flow onto roof

I need a plumber / roofer to replace part of down pipe spreader to me. Nothing wrong with the spreader but the water drips onto the iron roof not the tiles which makes it super noisy when it rains. I need it to be extended to tiles or anywhere that doesn’t let the rain drop onto the metal part of the roof

1.Re affix down pipe to side of house. 2.Install new taps and spout to bath, hardware provided 3.Install new taps and spout to kitchen sink, hardware provided

The pergola downpipe currently goes nowhere and we need to get this connected to the storm water. We would also like install a strip drain between the pergola concrete and pool concrete to connect to the same drain.

Painting top and bottom edges of front and back door and three doors in bathrooms, paint some down pipe, and one spot in hall way

Supply and install a colour bond downpipe to an existing gutter down to the channel drain in front of my garage. I’m open to other reasonable installation advice. There are not enough downpipes so the gutter will overflow during heavy rain. Straight forward job and easy access and single floor.

When it rains, water pools in one corner of my gutter and overflows like a fountain. The gutters are clear of debris but I believe they are on a very slight slant leading rain to build up in this corner and rush over the edge. I need someone to replace the piece of rotting wood underneath this corner of the gutter (see images) and install a downpipe so that water can effectively drain from this area in the future.

Amend the 5 downpipes shown to make room for electrical conduit to run under the downpipe on top of the brickwork capping, also use pvc pipe to remove the sharp 90 degree angle to reduce rain noise.

Drain at bottom of downpipe is blocked. Material is quite hard, Suspect organic shave been growing in it? Need to clear it.

The down pipe fixed or replaced please. It’s leaking into my garage.

I need a rusted guttering down pipe replaced. 102mm x 78mm square down pipe 4” x 3” 520 mm top section length. 2440 mm down section

Supply and install PVC pipe and fittings to downpipe. Circa 3m lg - refer photos

Needing to solve a heavy rainfall issue where the water ends up in my garage the drain next to the downpipe does not get rid of the water it’s like a supplement drain with limited drainage. Looking to install a rainwater diverter on the downpipe so that I can divert the water to another drain closeby to stop my garage getting flooded hoping someone can assist