Find trusted local electricians in Melbourne

Electrician to swap existing hardwired down light to a 3 pin gpo like connection in ceiling. I have new transformer ready to go.

Replace 2 ceiling light Rewire one of them

My hot water system decided to not to play nice and stop working as I moved in. I have bought a new hot water system. Need the other one disconnected and this one connected. Both natural gas hot water systems. Approval for it to be externally put on the wall.

I need an electrician to do a few work at a cafe, connections etc. You will need to complete it this weekend. If you are keen, I can first show you the stuff the needs to get done today. Please let me know asap

Need an electrician to check out the wiring behind our front porch light , and ensure it’s all working properly with a new bulb installed. The last few times i replaced the bulb, it burnt out within a week. Thinking the wiring should be checked.

Wire a scone onto wall and add a switch with dimmer. Wall is plaster.

Looking for a licensed electrician in Melbourne to replace 4 existing ceiling light fittings with supplied pendant cord sets and shades. * Existing wiring points already in place * No relocation of wiring required * Approx 3m timber ceilings * 2 lights in living/kitchen area + 1 in each bedroom * I will supply pendant cord sets, shades and bulbs * 2 shades require assembly * Need installation and testing only * Must be licensed and provide Certificate of Electrical Safety (COES) Apartment is in Carlton.

Have some VEU air conditioner project, need electrician and provide certificate. Please feel free to give me a quote.

ELECTRICIAN Title: Licensed Electrician — Full Electrical, Communications & Lighting · Commercial Venue · Melbourne CBD We are opening a new hospitality venue at 66 Hardware Lane, Melbourne CBD and require a licensed electrician for a full electrical, communications and lighting scope. Works must meet commercial compliance standard and all certificates must be provided on completion. Power Points Test all 240V power points across the venue — approximately 45+ outlets Fit covers to all uncovered power points — compliance requirement Make safe all hanging ceiling GPO outlets above kitchen work area Repair faults found during testing Communications & Data Full audit of existing cabling — identify, label and document all cables Remove all redundant and dead cables Properly terminate and patch all active data cables Secure and dress all cables — no loose cables on floors or walls New cable from building MDF to internal IDF board as required Wifi connection check and rectify as required Lighting Fix and repair 5 broken ceiling lights throughout venue 5 lighting repairs throughout Certificates & Compliance Certificate of Electrical Safety (CES) — legal requirement, Victoria Inspection certificates — power points, communications, lighting Important notes: Licensed electrician required — no exceptions Commercial compliance standard throughout This is Step 2 in a compliance sequence — handyman works complete first or simultaneously Quote to include all labour and materials Timeline is urgent — works to commence week of 3 June Location: 66 Hardware Lane, Melbourne CBD Budget: $3,500 — includes all labour, materials and side inspection

I need a certified electrician to fix a smoke alarm that is hanging from the ceiling. It may need to be replaced with a new one, so I would appreciate some advice as well.

One of the power lines constantly trips the main switch board. We are Having an issue with a specific Plug point as well ; when we plug anything into it, the line trips.

I have a client that has a hot water heater not working. They need someone to come out today. My plumber is not available. Need someone to come

Two wall mounted lights installed on wall and connected. They will be installed ons brick wall so there will need to be some conduit run from ceiling. There is easy access to ceiling directly above proposed installation spot. There is also power and a pre existing switches that could also be used

New smoke alarm installed

I need an electrician to come remove 2 outdoor wall-mounted lights and install 2 new ones (hardwired), which we will supply. Should be a quick and easy job for a good electrician. Need this done Saturday.

Two pendants need installing in the place of down lights. The down lights are in a grid of four so we will disconnect two. We also want to add two dimmers - one for the new pendants and another for separate lights that are on their own switch. We have all the fittings. The pendants are made out of papier mache and coffee beans, so not heavy but not paper light.

Safety switch turned on, lights in the house work fine all plugs stopped working , trying to identify which plug is faulty and fix it.

Please replace one failed integrated LED downlight. I think It’s a 6W IC-4 Lute Lighting downlight. Please buy whatever you need or I can go buy from Bunnings as well. Just not sure if the above is correct. Happy to go get it. Please quote accordingly whether you will bring the bulb with you or I should go buy first Thanks See photos. I thought it's a normal bulb and tried to do it myself but quickly realised it's not I work from home so any time is okay.

2 halogen down lights on a dimmer circuit require new transformers (you supply) 1 LED down light requires new transformer (you supply) Replace laundry exhaust fan (I supply) Replace outdoor power point on driveway (you supply)

Hello, We are looking for a licensed A-Grade Electrician to repair a faulty light in the back/staff area of our retail store, on Chapel St, South Yarra. The Issue: A fluorescent batten light in a staff area at the entrance to our back room has gone out, making the area dark and affecting staff safety. The Job: The task is to restore the light to full working order. The scope of work includes: 1. Attending the site to diagnose the fault (e.g., blown tube, faulty starter, or failed ballast). 2. Supplying and installing the necessary replacement part(s). This may be a new tube and starter, or a complete new like-for-like batten fitting if the ballast has failed. 3. Testing the light to confirm it is fully operational. Requirements: - MUST be a fully licensed and insured A-Grade Electrician in Victoria. - You must be able to provide your license number. - You must have your own tools and a suitable ladder. - You must be able to supply the replacement tube/starter or a complete new standard batten fitting as part of the job. Location & Timing: Location: Chapel St, South Yarra VIC 3141 When: The job can be completed at your earliest convenience. Please state your availability in your offer. Please provide a comprehensive quote for the complete job. Your offer should include your call-out fee, all labour, and the cost of supplying either new components or a complete new batten fitting. Thank you.