Find trusted local electricians in Melbourne

Install two smoke alarms to replace the ones already there. Cert required

I need installed 2 double Clipsal Weathershield single outdoor power points (GPO), there is one already installed 2 meters away, so you may be able to move that one and source power from there. Plus, Relocate a Pierlite BWP/T236EL IP65. It is a legacy 1200mm (4-foot) twin-tube IP65 weatherproof fluorescent batten one meter away. Check a fuse for a 3 phase switch that no longer seems to be working.

I need to close a box that has a wire running to it from the power lines but I don’t have a ladder tall enough. Would love for someone who has a ladder to swing past on their way home from work and shut it.

Left front side mirror needs replacing. I have the new mirror. 1 front head light bulb needs replacing. I have the new bulb. Car is a Vw amarok 2018 with a bullbar

Friday Electrical desk install required. Will need cabling to run across ceiling, and the drop down to two desk configurations, using an umbilical cord from ceiling to desk, and connecting desks, and desk lights. Needs to be a licensed electrician, able to work on Friday until the job is complete. The desks / cabling is the same as shown in the picture (desks have been relocated to new office)

I'm looking for a licensed electrician to complete the following: Installation of 3 pendant light fittings (pendants supplied). Repair of 1 existing light fitting. The plastic lamp holder/casing that holds the bulb has broken and needs to be replaced. Please provide: A quote for labour and any additional materials required. Your availability. Confirmation that you are licensed and insured. Happy to provide more photos of the existing fitting and pendant lights if needed.

7 lights to be installed (pre existing fittings) and 2 new power points. The lights are like in attached photos, 3 flat on the ceiling, 2 hanging from the ceiling and 2 flat on the wall. For power points, there is a power point for a dishwasher under the bench about 2 m away. Parking on site available.

Looking for someone to change a down light bulb

Need a licensed electrician to: * Redirect the ceiling light-switch wiring and install the switch on the nearby wall. * Move the exposed switch shown in the second photo to the opposite side of the wall. Wall framing is open for easy access. Quote must include labour, basic materials, testing and safety certificate. Location: Coburg Budget: $350

I’m looking for a licensed electrician to install one new double power point on a plasterboard wall in my apartment. There is an existing double power point approximately a few metres away near the marble shelf, which I’d like the new outlet to potentially be supplied from. The job: * Install 1 x standard double GPO underneath the existing picture frame (see photo). * Ideally run the cable inside the plasterboard wall cavity from the existing power point. * I want no visible cabling or plaster chasing between the two points. * Only the necessary cut-out for the new GPO. * Please assess whether the existing GPO/circuit is suitable for the additional outlet. * Supply and install the GPO. * Test and leave the installation compliant and tidy. * Licensed electrician only – Victorian electrical regulations apply. Budget: $250–$300 Seeking a fixed price agreed before starting. Please quote including labour, materials and installation and confirm you are a licensed electrician in Victoria. Photo attached showing the existing socket and proposed location

Electrician Needed – Monday Morning Looking for an electrician available Monday morning to connect/install the following: - Electric hot water unit - Dishwasher - Cooktop - Oven - Rangehood All appliances/units are already on site and ready for connection

Licensed Electrician Required: Workshop Rough-In and Final Fit-Off Looking for a qualified and licensed electrician with solid rough-in and fit-off experience for a small new workshop. IMPORTANT: The workshop has open framing with no plaster installed, so wall and ceiling access is clear. The job will be completed in two stages. Stage 1: Rough-In Rough-in wiring for 1 hardwired interconnected photoelectric smoke alarm Rough-in wiring and positions for 6 dimmable LED downlights Rough-in wiring and mounting positions for 5 quad GPO power outlets Install 2 Cat6 data runs from the main house to nominated workshop locations Rough-in wiring for LED bias lighting and smart wall dimmer/control Install and prepare all switch, dimmer and control positions Supply all electrical cabling, Cat6 cabling, connectors and standard consumables Secure all wiring and leave the workshop ready for plastering Stage 2: Final Fit-Off Return after plastering to: Install and connect smoke alarm, 6 supplied downlights and 5 quad GPOs Install switches, dimmers and smart lighting controls Terminate and test both Cat6 data runs Complete LED bias lighting setup Test all circuits, lighting, outlets and data points Provide required electrical safety and compliance documentation We supply: 6 LED downlight fixtures Electrician to supply: All cabling, Cat6 cable, smoke alarm, quad GPOs, switches, dimmers, data outlets, connectors and standard consumables Requirements: Qualified and licensed electrician Experienced in residential or workshop rough-in and fit-off Registered to complete and terminate data cabling Own tools and testing equipment Work completed to Australian electrical and cabling standards Available to return for final fit-off Please quote for both stages, including labour and electrician-supplied materials.

I need my Generator, Bain marie, and 3 extension leads tested and tagged before this Friday night

Looking for a licensed electrician to carry out an electrical safety inspection and issue a Certificate of Electrical Safety (COES) for two small, adjoining retail shops (25 m² each) in Melbourne CBD. Power has been disconnected during vacancy, and the distributor requires an official COES to turn it back on. Exactly What Needs to Be Done Switchboard Assessment: Inspect circuit breakers, RCD safety switches, earthing, and main switches for both units. Electrical Safety Testing: Perform mandatory testing (insulation resistance, polarity, earth loop impedance, and continuity). Visual Inspection: Quick visual check of power points, lighting, and accessible wiring across both 25 m² spaces. Main Switch Protocol: Ensure main switches remain safely turned OFF ready for distributor reconnection. What Is Required at the End Official ESV Lodgement: A Certificate of Electrical Safety lodged directly through ESVConnect (Energy Safe Victoria). PDF Copy: A digital copy sent immediately so it can be provided to the energy provider.

Looking to hire a licensed electrician for 3-4 hours work to replace some smoke alarms and old power points and troubleshoot a lighting problem and issue COES for works. Seeking price for call out fee and hourly rate. Alarms and power points will be supplied. Interconnection line will be pre run to pull through cable.

I’ve got a garage studio where the power occasionally trips when high-power appliances like the kettle, washing machine or heater are being used. I believe the garage and some of the downstairs power points may be running on the same circuit. Could you please assess whether the load can be redistributed across the existing circuits, or whether it would be better to install a new dedicated circuit? I’m just looking for the most cost-effective way to prevent the power from tripping.

We’re looking for a licensed electrician located near Port Melbourne for a small, straightforward job at Port Melbourne . The work involves: 1. Repairing or replacing the damaged/cut electrical cord on a large illuminated full-length mirror and ensuring the lighting operates correctly. 2. Reconnecting the loose lighting wires from a light-up sculpture to its existing LED transformer/driver. 3. Properly configuring and securing the transformer and fitting a suitable power lead and plug so the sculpture can be safely connected to a standard power outlet. 4. Testing both pieces to ensure they are safe and fully operational. The mirror, sculpture and existing transformer are onsite. Please bring any suitable replacement cable, connectors, plug and electrical fittings that may be required. Location: Port Melbourne, VIC 3207. This should be a relatively quick job for an experienced electrician. Ideally, we would like someone local who can attend as soon as possible. Ideally prefer 3pm today

Chasing a licenced electrician. We have installed some new counters in a shop in cbd. There is existing supply from old counters. We need to install the below. Wire up 10 power points, Install 2 x plug bases. Connect 1 extra feed into power point to liven up, cable in ready to go. All materials supplied. Upon completion we require a COES for the works you have done. Plenty of car parking ( free ) Ground floor with easy access. You can park within 15m of the site. I have allowed 4 hours labour.

I need a new on/off switch on my bed side lamp as it’s flickering. I also have a floor lamp that needs a new wire (arrived faulty)

I have a large skylight I would like to install on my roof. I am looking for experienced help to oversee and assist installation. I am handy and happy to do most of the heavy lifting etc but specifically looking for someone who is either in the industry or WELL versed in this kind of installation to help with the finiky side of things. I am specifically NOT looking for a second well to do handyman like myself. PLEASE ONLY MESSAGE IF THIS IS SOMETHING YOU ARE AN EXPERIENCED PRO AT. Additionally I have two other skylights which have been leaking and i would like some friendly professional advice on how to fix. To clarify I am only seeking help installing, watertight, onto roof. No need for shafting/plastering etc on the inside. Skylight is a standard Velux and I currently have the corresponding flashing. Roof is a pitched Terracotta Tile (1st Floor)