Find experienced local carpenters in Kew VIC

Hi, I’m looking for a qualified carpenter available on Friday, 4th of July, for 8 hours of work in Abbotsford. The job includes framing 2 balconies and building 2-step stairs. Please message me if you’re available or interested

Paint kitchen joinery including replacing hardware, possibly replacing bench surface

Have about three areas I want to close up to stop any critters entering the house. A couple need a small piece of wood to close the gap and then fully sealed. Plus other little areas I want to have caulked or expandable foam to close up where wood is difficult. Don’t have photos of the all areas as I will need to remove a cupboard for one of these, but one of the areas shown.

I have a 3m long solid oak dining table and looking for a handyman who has had experience in sanding and staining furniture, to help me finish it as I am moving house. The table is currently in my double garage and the work can be done there, so no need to move it. I have already stripped / sanded the table top, just need you to sand the legs and apply a stain in a walnut colour. This needs to happen this Saturday, I expect there is approximately 4 hours work here and I will purchase the stain.

We are seeking an experienced and reliable cabinet maker or shopfitter to complete unfinished counter and cabinetry work for our restaurant. 🗓️ Start: As soon as possible 💼 Type of Work: • Finalising counter installation • Completing cabinetry (doors, shelving, finish) • Installing hardware and benchtops • Ensuring commercial-grade finish • Optional: fitting sink/plumbing cutouts

After a quote for kitchen and laundry cabinets

Aluminium dining table frame painted black. Table top sanded lightly and stained black and TV cabinet sanded lightly and stained black

Fix gaps in wooden floors. Have come loose - movement. Someone with experience please builder or floor installer. Open to offers. Thanks

Check picture. Cut King size timber to half. We transport to upstair. You make timber cleat to enable 2 cut pieces joint together with flat surface.

Cut, take panel to upstair and re joint the panel. Panel is king size bed, used as hard mattress. 1 side MUST have plain surface. We do this because it’s too big to move to upstair. How can we do it to make it transportable myself if one day we need to move it to down stairs again ? No cutting again Quote and advise how you will rejoint it.

I have a front study room that i'd like wall panels added too on all three walls and ceiling (i've attached a reference photo of what i'm after). I want the entire room covered with this veneer. I have the veneer (58cmx250cm) - these will need to be applied to a thin plywood (or MDF) and then applied to the walls and ceiling. The room is approx. 2.8m long x 2m wide x 2.1m tall. I have attached a photo of the room (currently painted in green).

am hoping to get 2x BROR cabinet with 2 doors built. They are from IKEA. I am then hoping to have them safely installed into a laundry wall. Thanks!

replace rotten timber window sill (approx. 2.5 metres in length) and bottom part of timber window frame (photos attached)

I’ve refinished a side buffet cabinet and installed the hinges on the doors, however installing them on the actual cabinet is proving to be beyond my level of skill. You’ll need to indent the cabinet, I have already (poorly) done this with the doors. There’s 6 hinges in total (2 for each door).

Filling gap in one timber floor board

I would like to remove the open shelves from my kitchen island bench and build closed cabinets along the entire area where stools were supposed to go.

I am getting 10 sheets of timber veneer board made: each is 3m x 1.2m. Each of the 10 boards needs to be cut down to 2900 mm x 705 mm. Then we need to apply edging to each of the2900 mm length.

Hi Jamie, How much do you charge for your carpentry work? I have some work to be done around the house.

I have 2 small side tables with timber tops. They are 300mm X 300mm. I need the tops stripped back, stained and varnished. I would prefer a darker colour to the present finish. The tops unscrew from the bases and are easy to handle.

Open up a hole on the bottom of a drawer from underneath. The hole needs to be large enough to put a hand through.