Book a trusted oven repair and installation expert in Melbourne

1. The inside glass of the oven door is no longer fixed. Looks like an adhesive has disintegrated. 2. Ignition on gas cook top has stopped working

Need 5 holes drilled to ventilate my oven properly. The photo with the square is the current ventilation and the second pic is what I need

We need a electrician to come disconnect the oven from a wall. It seems to be connected to a junction box and we thought it was just a plug. It’s a electric oven

Our Andi gas stove and oven require repair for some functions. Gas stove: the bottom two knobs don’t turn (have tried pliers and grease). Also, the pilot doesn’t work to ignite - we’re using a lighter for the three sections where we can turn on the gas. Oven: most of the functions work, except for the first two (turning the knob anti clockwise). See photos attached. Qualified professionals only thanks.

After some assistance to have a gas oven disconnected before the electric oven is put in. Oven is free standing gas - if you can take it as well, that’s great. Not essential though!

The double oven in the photo is to be replaced by two ovens. As I see it: Step 1: remove existing oven (no electrical work, connected via plug, quick and easy) Step 2: cabinets - remove cover panel and drawer below oven; remove shelf that existing oven sits on and enlarge opening at the bottom; install new shelf at required height (lower than existing); install new cabinet on the new shelf (new cabinet is already built); reinstall drawer (a bit lower than current); reinstall cover panel under drawer (cut down in size). Step 3: install new ovens, one in top section of new cabinet, one in bottom section. Plug them in (no electrical work - 15amp power point). Other points: 1. No electrical work involved. Current and new ovens plug into power points. 2. Existing cabinet is wider than needed for new cabinet. New cabinet will fit inside existing cabinet once it is enlarged at the bottom. 3. Final detailing (new laminex front panel) to be done later, not part of this job. p.s. I'll be available to assist - e.g. lifting the heavy stuff like the existing oven, new cabinet. p.s. job adjusted - to prepare quote for the work.

I have a whirlpool Oven model 6AKZ452/IX/01. The start button suddenly stopped working after I had unplugged it. It’s a 20 amp electric switch. The switch is working fine. Need someone to come and make it work. They will also need a to provide a 20 amp connector. Thank you

My oven element isn’t working. (Kleenmaid professional). The grill function works, but fan forced oven setting doesn’t. We think an element needs replacing.

My oven has stopped working the lights still on but nothing seems to be working. When I turn knobs it just gives me nothing.

* Replace an old Bellini BOT608X-F oven with a Miele Steam Oven ( DGC 7250). Model requires 16A. The plug is in place. I have attached a picture of the Switchboard. * Install an outdoor double plug on the brick wall for the hot water system. There is a plug indoor close to the unit.

Miele oven stopped working

I’m in Moonee Ponds and I need a new oven/stove connected and the old one disposed of by a qualified electrician.

Here is the photos of kitchen, have separate line for oven and rangehood already. need to finish up circuit connection for induction cooktop(see photos for progress). Please note you will need to supply cooktop safety switch that can be integrated into existing power point seamlessly without needing extra holes for seamless look - refer to photos for placement. New appliance are Bosch- here are serial numbers for reference if needed Oven: Bosch – HBG976MB1A - line exists Cooktop: Bosch – PVS631HC1E - finish line connection(pre drilled holes) Rangehood: Bosch – DBB67AM60A - line exists Also will need LED lights installed in cabinets(have two of them for each side of range hood) to be connected to the power point on top. Have LED channel as well)

Hardwire oven. New oven, with wire ready to connect.

Hi - I am getting the floors re-done and need an electrician to disconnect the oven this week. At the time of installation, the previous electrician needed chain it to the wall for manufacturer warranty purposes, so it will need to be disconnected there too. Happy to answer any questions. Many thanks.

Inside panel of tempered glass in oven smashed. Need a new panel installed

Install only required by qualified electrician to fit 60cm new electric oven. Required on Wednesday July 9. Old oven has already been removed. Make and model below. South Melbourne home. https://www.appliancesonline.com.au/product/emilia-60cm-stainless-steel-electric-multifunction-oven-emf69e/?origin=product-search&kwd=&gad_source=1&gad_campaignid=185901768&gclid=EAIaIQobChMIq-O4t8qQjgMV4KlmAh14FSXbEAQYASABEgKdHfD_BwE

I have a new Bosch oven which comes with a power cable that needs a 16amp plug fitted to it or to be hard-wired in, I already have a 16amp socket on the wall

to change the adapter to a new oven

I have a new oven that will need a 15A plug fitted There is a dedicated cable running in the wall from the switchboard that hasn’t been installed (will need to be fitted into switchboard) And a 15a gpo installed at other end. Summary Oven fitted with a plug GPO connected & installed in wall Switch installed and connected in switchboard Must be licensed to certificate work done ✅ Have own tools 🧰 There is no chasing to be done as cable is already in wall and new cabinetry has not been installed so no need to move around things.