Find an experienced handyman in Dee Why

I’m replacing old locks/levers on 3 internal doors with new Gainsborough Matte Black Choice Harper Square Privacy Lever Sets (60mm backset, 54mm bore, 25mm edge bore — I’ll supply the handles, latches and instructions). The old hardware has already been removed. Scope: 1. Patch 2 door edges: two doors had mortice locks, leaving rectangular cavities in the door edges. These need solid timber infill blocks, glued and packed tight, planed/sanded flush — the new 25mm latch bore and faceplate screws go straight through the patched area, so it must be solid. Please bring suitable timber and adhesive. • Door 1 (bathroom): cavity approx. 100mm high x 17.5mm wide, door thickness 34.8mm • Door 2 (second bathroom): cavity approx. 57mm high x 16mm wide, door thickness 34mm • Please verify cavity depth on site — I haven’t measured it 2. Drill new holes in all 3 doors: 54mm face bore at 60mm backset + 25mm edge bore. Third door (bedroom, 34mm thick) has no cavity — drill and fit only. Note: all 3 doors have existing old spindle holes (~14–23mm) that overlap the new bore centre, so a hole saw pilot bit won’t have material to engage. You’ll need to clamp a sacrificial board over the face to guide the hole saw, or use a lock installation jig. The old holes fall entirely within the new 54mm bore and will be drilled away. 3. Install the 3 lever sets including latches and strike plates, chiselling strike plate recesses in the jambs as needed, and confirm doors latch and the privacy function works. Doors can stay on their hinges. Painting/finishing not required. You’ll need a 54mm hole saw, 25mm spade/auger bit and chisels.

Looking for an experienced installer to remove my existing bath screen and supply and install a new sliding screen over the bathtub. The setup: bath sits in an alcove with a tiled hob on both sides and tiled walls to ceiling. There's currently a single frameless fixed glass panel at one end attached to another panel which moves and allows entering the bathtub, which needs to come out. I'm after a 4-panel configuration to replace it — fixed panel at each end, two sliding panels in the centre, running on top and bottom tracks. Photos attached, including one with the layout marked up. Open to your recommendation if a different configuration suits the opening better. Scope: Removal - Remove and dispose of the existing frameless glass panel and its wall channel - Cut out and clean off all old silicone - Fill any redundant fixing holes in the tiles ————— Supply and install - Measure the opening on site and source a screen to suit - Supply the screen: Grade A safety glass compliant with AS 1288 - Mount wall channels into existing tiles without cracking them - Fit top and bottom tracks to the tiled hob, level and plumb - Hang and adjust sliding panels so they run smoothly and close square - Silicone seal externally with neutral-cure mould-resistant silicone, leaving the internal base so water drains back into the bath - Clean up and remove all glass, packaging and offcuts from site Please include in your quote: - Removal, supply and labour itemised separately - Brand/model of screen and glass thickness, plus finish options (I'm interested in matte black) - Warranty on the product and the installation - Whether you're licensed and insured - Any photos similar screen installs you've done would be great - Lead time and availability If you'd like to inspect and measure before quoting, let me know and we'll arrange a time.

Looking for a qualified/licensed glazier or window/door installer to replace an existing balcony sliding door/window system in my first-floor apartment in Dee Why. Opening size: approximately 2.33m wide × 2.09m high Current system: * Approx. 3 panels * 2 glass panels + 1 flyscreen/mesh panel * Existing flyscreen is damaged I would like to replace the whole system with: * 2 good-quality glass sliding panels * 1 sliding flyscreen/mesh panel * Coastal-grade materials suitable for Dee Why * Good corrosion resistance, with stainless-steel hardware where appropriate * Professional installation * Removal/disposal of existing system I’m looking for good quality at a reasonable price, rather than a premium/over-engineered system. The apartment is first floor with a balcony, so there is no direct ground-level access. Please provide a quote including: * Supply * Installation * Removal/disposal * Glass and frame specification * Flyscreen specification * Warranty * Any additional costs Final measurements can be confirmed on site before ordering.

I need two ceiling fans replaced. The remote also connects the downlights. Fridays would be best or a weekend.

https://www.ikea.com/au/en/p/pax-grimo-wardrobe-with-sliding-doors-white-white-s29598796/ X 2 One half sized one, no sliding track https://www.ikea.com/au/en/p/platsa-wardrobe-with-5-doors-3-drawers-white-fonnes-white-s49624997/ X 2 Waredrobes are already assembled, we just need to put the sliding track and the waredrobes into the wall

Install, not build so less time consuming! Need someone with experience Also need to cut a space for the GPO, Sliding waredrobes to be installed Need you to bring the tools and other things, we might need to go to Bunnings I would pay. https://www.ikea.com/au/en/p/pax-grimo-wardrobe-with-sliding-doors-white-white-s29598796/ X 2 One half sized one, no sliding track https://www.ikea.com/au/en/p/platsa-wardrobe-with-5-doors-3-drawers-white-fonnes-white-s49624997/ X 2

I need a small painting affixed to my wall and my bathroom cabinet fixed.

Repair cornice in 2 bathrooms. Damage is only in a small area within the shower area.

Install 8x3 metre shadcloth over driveway. Dee Why. Should just be 4x tight D-Link or loop hooks drilled into the side of weatherboard house, garage brick and one corner bolted onto a timber post attached to fence. You will need to fix a strong post to the fence to attach 4th corner. Can share photos but will supply materials if you confirm what works best. Simple job for right person

Fix and repaint the part of the false ceiling that has water damage.

See photos attached. Need rubber seal replaced on kitchen sink waste. Slow leak developed overtime, assuming just the rubber gasket needs to be replaced and tighten.

Supply and install a single wardrobe sliding mirror door to replace one of the two existing sliding white-glass doors(preferably the back one). The dimension of a single current existing white glass door is 119cm(width, this can be flexible up to 125cm if there is a supply problem) x 230.5 cm(height). Note that I will keep the replaced sliding door for backup and practical purpose. In other words, not to be taken away.

-Install sink and tap into new bench top. -Adjust plumbing to suit sink hole location. -Replace 2x faulty shut off valves (I have put vice grips on the pipe to stop it)

I have tried using my own basic drill and it takes forever. Proper hammer-Rotary drill required. Four curtain rods four holes each - 16 total holes need to be drilled in solid concrete walls. I have marked location of screw holes already. The walls are rock solid!!

Reciever for ceiling fan replacement. Use existing wiring Needs to be cost effective

Repair set and patch approximately 2 m² of Chiprock in a bathroom ceiling. No painting required. Just get ceiling set and ready to be painted.

We have 2 metres of cornice that needs to be installed above a closet.

Fix flyscreens on a window and retractable screen

Repair minor leaks including materials

Install 3 ceiling fans in 3 rooms