Find trusted local electricians in Melbourne

I need someone to: • Remove the old, non-working light from my shop sign. • Supply and install a new LED light (small and evenly distributed). • Clean the sign properly after installation. Details: • Sign is located high, you will need your own ladder/tools. • Power is ready and accessible. • Flexible timing – any time that suits you. • Budget around $120–$150 total (including LED light and cleaning).

Hi, the lights of the room just started to flickering and a cracking sounds is coming from the light switch. Need a electrician to please fix. 4 Led downlights. Pictures attached

Hi, I need a licensed electrician to replace a stainless steel Clipsal BSL15XA power switch/outlet unit in my kitchen. The existing unit's back mounting plate has fallen inside the cabinet wall and is not retrievable. The wood panel is fixed to the floor and rear access is not possible. I’m looking for: Either replacement with a compatible surface-mount power switch (if easier), OR an alternative method to securely mount a similar switch from the front, OR help retrieving/replacing the rear plate professionally (if possible without damaging the panel). Please bring any necessary tools and fittings. Photos of the current unit can be provided upon request.

Replace smoke alarm batteries x 4. 2 next to top of stairs but reachable by normal ladder

We have a new light shade to put on a pendant light but are unable to remove the existing pendant. It may need to be unwired. The shade aperture is too small to take off the existing fitting. We require someone with electrical experience to help us figure out how to do this job

Outdoor water pump is blowing the fuse so we turned it off. It needs fixing. 2 down lights outside that are broken/need fixing/replacing

Looking for a qualified electrician for the following jobs: - Install a powerpoint in each of the two bathroom cabinets (see photo). - Install a powerpoint in the kitchen under bench behind the draw (see photo). - Install a powerpoint in the kitchen island bench on the back (facing out, where chairs would sit) (see photo). There are nearby power outlets in all the above locations and they are all on internal plaster walls with the bathroom cabinet wood on the inside etc. - Install an outdoor montion sensor light, replacing an existing light socket, or using that light as a power source. Brick facade. (See photo) Optional if doable: - Where the TV is on the wall, install TV antenna through the wall from TV to the bottom which needs to go through the wooden stud in the wall. Existing holes for this top and bottom already exist. Cap/remove the two existing powerpoints behind the TV as they are not in use. Please let me know if you need any more information, photos, or would like to come by to confirm details before quoting.

Replace the ceiling exhaust fan. I have all the necessary component - fan, tape and ducting. It just needs to be installed.

I have purchase the LED light and it needs to be install installed on the back of the tv, the tv is mounted tv (attach to the wall)

Electrical job to replace a wired in downlight

Approx 7-8 of my downlights are now out and need to be replaced. I am not sure of the exact size/specs. Tasker will need to bring bulbs or include cost of bulbs in the quote. Would very much prefer bulbs that have a warmer more yellow light than harsh fluorescent / blueish light . Need the lights / bulbs to be dimmable. There is also one switch / one set of lights that is blown out and was surging before it blew out. So this may need to be looked at more carefully/ fixed .

Replace my existing 240v Smoke Alarm with a new one and install it where the current one is installed.

Seeking a licensed electrician to install two pendant lights and change a single gang dimmer over to a plain wall switch. We have one to be installed where the existing wiring is ready with screw connectors on it to be hooked up, and another that will need to be removed and replaced. The pendant suspension cords will need to be trimmed down due to how long they are. Also require the dimmer switch that controls one of them to be changed over to a single gang on/off switch, which we can supply. Thanks

Replace 12 x LED Downlights (add plug base). There are 12 LED in place (6 in lounge room, 2 hallway, 4 bedroom). I have bought Philips colour controlled IC4 to replace those. Current lights are wired to a connector. New lights have a plug and will be required to fit to plug base (these will be supplied).

Need a qualified electrician to remove a ceiling fan and reinstall a down light.

Burning smelled came from the switch which connect to bathroom lights and exhausted fans. Need the switch to be replace and fix Please send me quote includes everything (parts, labour, etc) to fix the issues.

A new light fitting needs to be put in to replace the old. New light here: https://www.beaconlighting.com.au/uno-250mm-1-light-flush-mount-in-black?queryID=eb9f40000dbd7ffb697329e09950f734&objectID=11508&indexName=beacon_m2_retail_prod_new_beaconretail_products You will need to be a qualified electrician. I will supply the light Thank you!

1) Change one light bulb (Fig 1) 2) Cracks on ceiling light shade (change the shade or whole light) (Fig2)

Hi. I need 38 hardwired downlights replaced with plug-in down lights. Plugs and downlights supplied by you in consultation on options with me.