Find trusted local electricians in Hoppers Crossing

I need Electrical, Gas and smoke alarm safety checks done by licensed professionals. Need to have a formal compliance certificate for all for rental compliance. Also need to have rental minimum standards compliance certificate. This is a 4 bedroom house along with a private granny flat. Need all compliance certificates for both

I'd like two seperate switches to connect to one (1) and then (2) for the multi switch to turn single 1 is (see pic) A and A to connect- currently switches on different walls. 2. Then the two Multi to connect also if possible to be one switch instead of the Multi. Thanks.

Its a newly built home. Aircon trips. The circuit breaker is less than whats recommended. I do not need certs for this work. Need circuit breaker replaced. And maybe run new cable to the unit. The unit is central one sitting in roof. We can negotiate

Hi 👋 my fuse box in my kitchen keeps on dropping when I use too many appliances at once in the kitchen, I have recently changed from a gas stove to induction stove.

electrcial works attached as images.

Sent me quote for job 23 Down light 10 old location New location 13 Total 23 Send me quote for each

I would like to add more powerpoints and downlights in my home, is this something you can do?

Remove and dispose of the existing faulty 90 cm rangehood. Supply and install Westinghouse 90cm Stainless Steel Universal Rangehood – 3 Speed. Configure the rangehood for recirculated operation, including appropriate filtration. Secure the rangehood in accordance with manufacturer installation requirements. Test and confirm correct operation upon completion. Make safe the disconnected induction cooktop by: Isolating the electrical supply. Properly terminating and enclosing all exposed cabling to eliminate electrical risk. Ensuring all electrical works comply with AS/NZS 3000 Wiring Rules.

Lights work but power points are dead. RCD stays on but won’t trip on test. Breakers reset. Suspect failed RCD or neutral fault. • Lights are working, but many power points are dead (kitchen outlets, fridge, living room TV). • All C16 power circuit breakers have been reset (OFF → ON) with no change. • The RCD / safety switch appears ON, but pressing the TEST button does NOT trip it. • This occurred after connecting a newly wired coffee machine, but the appliance is now fully unplugged. Suspect: • Faulty or failed RCD, and/or • Neutral fault on the power circuit. Request: (price includes marerials) • Test and replace RCD if faulty • Check neutral bar and terminations • Restore power to affected circuits and verify RCD trips correctly on TEST ⸻ extra context • Switchboard is Clipsal • RCD is Clipsal RCD240/30, 40A, 30mA • Lights circuit is unaffected • Power circuits affected span multiple rooms

few downlights not working around 10-15 light upstairs not working as well new connection needed in the shed area if possible

Underneath the eaves on one of the side sides of our house, is a whole bunch of wires and old Telstra boxes. I don’t thinany of these are hooked up to any electricity any more. I need someone to come in and clean them up so that the cords aren’t sticking out because we have a builder coming out to put eaves up.

I have a wall mounted boxed AC which is hard wired. it needs to be disconnected electrically and a GPO installed on the wall just underneath. Once that is done the AC will be replaced.

Switch board to be changed & 7 hanging lights to be hanged on roof

looking for the sub-contract work for air-conditioning installation. must have electrical business and insurance. every job must providing a certificates after job completed.

Outdoor lighting installation and other general lighting works around the house.

Smoke alarm won’t stop beeping. Have changed batteries. Need someone to reset. Clipsal fire alarm

Need 2 double GPO 10A installed for outdoor one in the front and one in the back

recently installed electric pool heat pump, but installer said that we required electrician to install new circuit breaker and power point is capable of it ? please check photos and quote need help

Hi there, I’m looking for a qualified and licensed electrician to carry out the following work: Job details: Replace the existing tube light in a room with a new dimmable lighting setup (so brightness can be adjusted depending on the time of day). Install a dimmable switch (photo attached) for the new lights. Require two lights to be installed in total for the room. The kitchen tube light is not working – please inspect and, if it needs replacement, use the existing room tube light for that area. Requirements: Please quote including the supply and installation of suitable replacement lights and dimmer switch. Must be a qualified and licensed electrician. Tax invoice and electrical compliance certificate will be required upon completion.

Need an electrician to replace the safety switch